anycubic photon leveling build plate 3d models

I didn't want to wait on a Wham Bam plate because I had prints that needed to get done so I ordered the Sovol plates from Amazon. They had a slightly different height recommendation (2.7mm) so I remixed this adapter in Tinkercad. ...Not only were they...

This adapter replaces the rear exhaust plate of the Anycubic Photon and allows you to connect the printer directly to a standard 40mm vacuum hose. * The other adapter adds a turbine cooler to force air into the tube. Model: Turbine Cooler...

Anycubic Photon S Screen Seal Protects Against Resin Spills. The seal effectively prevents resin from leaking into the machine, ensuring smooth operation. To install this screen seal, a vinyl cutter is required for precise cutting.

... https://www.thingiverse.com/thing:3006515. ... My part seamlessly integrates on a Anycubic Photon S. Begin by delicately removing the upper plate. Next, carefully unmount the fan and carbon filter. ... Proceed to solder the wires with the new fan.

drainer Anycubic Photon mono xthere is no need to remove the screw because it passes without any problem

drainer Anycubic Photon mono xthere is no need to remove the screw because it passes without any problem

A safeguard against accidental shutdown of an Anycubic Photon 3D printer. Additionally, the USB drive is now more secure against outside interference. ... Idea from: https://www.thingiverse.com/thing:3422406 www.deepl.com

hinge for anycubic photon mono. ... bom M3X10mmX2 hex socket low head cap Screw M3X4mmX2 thermal inserts 608 ball bearing(22mm OD 8mm ID 7mm thick )

I made it for anycubic wash&cure using photon zero resin printer. maybe you have to fine proper bolt and nut. refer following video. ... https://youtu.be/GewI4NBa6AQ

hinge for anycubic photon mono. ... bom M3X10mmX2 hex socket low head cap Screw M3X4mmX2 thermal inserts 608 ball bearing(22mm OD 8mm ID 7mm thick )

hinge for anycubic photon mono. ... bom M3X10mmX2 hex socket low head cap Screw  M3X4mmX2 thermal inserts 608 ball bearing(22mm OD 8mm ID 7mm thick )    

This is a function 3d design of a 3d printer. ...When i made this print i printed it out iwht my anycubic 3d printer photon mono. ...To buy this printer go to ANYCUBIC.COM

This adapter allows you to hang the build plate, so that the the uncured resin can drip off.I made good experiences with such an adapter on my Mono X, so I thought I create my own for the Anycubic Photon Ultra printer.Changelogv2 - 2022-04-05Updated...

A stylish sillouette of the famous AnyCubic Photon 3D printer. This can be created as a pendant, earring, brooch, tiepin, cufflinks, etc. and painted in a range of metallic tones for a glamorous finish. ... #ANYCUBIC3D

anycubic photon mono drain bracket. ...put on without removing the platform other accessories: https://www.thingiverse.com/thing:4912979 https://www.thingiverse.com/thing:4912997 https://www.thingiverse.com/thing:4923159 ...

Washing machine for Anycubic Photon S with support for 3d printer table attached directly to the capOn the bottom of the tub just buy a USB dishwasher to wash the piece

This is a remake of https://www.thingiverse.com/thing:3520264. ...I adapted those feet to match the Anycubic Photon rubber feet, resulting in a substantially quieter printer and workspace due to reduced motor vibration and table resonance.

This mod allows for an installation of an Noctua NF-A4x20 FLX (40mm) fan in your Anycubic Photon printer. ...This is primarily because the original fan had an bearing failure and was obnoxiously loud.

Anycubic Photon Parallel Led array for Parallel UV Light Source from Chitusystems. Different type of body, not like on the picture. https://www.chitusystems.com/product/5-5-6-0-inch-parallel-uv-matrix-led/ For installation in the Photon case. ...See...

The parts included in this design are: * Feb frame parts (feb1_v1 & feb_2_v1) * Resin tray v2 * Clamp for securing the upper build plate on the Z-axis * Build plate upper and lower components (which require re-creation) * Knob for locking the clamp...

I have a resin 3D printer, an Anycubic Photon Mono 4K specifically. When I print things, the buildplate remains wet and a lot of resin gets wasted when I remove the part and clean the plate, so i designed this drainer so to make the plate drain...

Hose adapter was used from Anycubic Photon Air Vent System by Creative-Process https://www.thingiverse.com/thing:3318738 Corrugated panel was used from Corugated iron by stewartmiller https://www.thingiverse.com/thing:2364932 2200 RPM...

... possible for the M3 bolt to loosen over time. To prevent this issue, consider updating to a nylock nut or adding springs. Since my build plate is made of ABS, which can withstand exposure to the plate, I print with PLA at temperatures below 70C.

... XY plane. Practice with a level build plate is key, as it improves over time. Use a low temperature when printing this part for better results on miscalibrated surfaces. ...Visit http://www.woodsmokeworkshop.com/wordpress/?p=209 for more discussion.

Two easy solutions to eliminate hazardous fumes from your space when operating the Anycubic Photon.\r\nOne option involves installing a removable ventilation unit at the back of the printer using screws instead of the standard factory-installed cover...

just a holder for the build platform of my Photon 4K holds it at an angle to getter a better resin runoff to the vat

To get optimal results, I recommend printing it at a layer height of 0.2mm and monitoring the build plate's adjustments as you print along - ensure your build plate is levelled before starting, by the way. If the infill lines do not align properly...

# Anycubic Photon Mono "Tray Dripper" This "thing" is a bracket that sits on the top of the build platform and allows you to easily tilt the platform to assist the resin in dripping off :) ### A update will be coming soon to correct the issue of the...

To achieve optimal results, make sure your build plate is properly leveled before starting print jobs. If infill lines don't align as expected, try adjusting the build plate screws upward. Conversely, if infill lines appear thin and see-through,...

This is a bottle drainer for the Anycubic Photon M3 Plus. The lid can be put back on while using it to protect the resin from dust and light. This can be left in place after use without interfering with the print process. The bottom slot is 40mm x...