anycubic photon mods 3d models

You can store the UV resin you're not using in these caps, which will protect it from light and dust by placing it in a tank container. ...By printing the two caps in PLA, you can use the bottom one to preserve the FEP.

This filter tower can be easily attached to the interior fan without any change. Add an active carbon filter. ...I recommend to remove the filter below the fan.

You're using a tube from a drying cabinet, outside diameter 105mm. The same screws and position are used as for the transparent lid. An old nylon stocking is employed to prevent dust particles from falling into the resin. The transparent tube...

The new lid from KayIOA didn't fit properly on my newly purchased vat. Check out the picture of the original vat (on the left) and the updated one (on the right). The smaller spout made it impossible for the lid to sit flush on top of the vat. To...

Hello folks! Here's a handy funnel that helps you filter your resin without driving your wife crazy:). As a filter, consider using your wife's tights, folded in two or three layers - it's a simple solution. You can always give the tights mesh a...

I detest forcing hinges and risk scratching the paint. This is a straightforward door stopper printed on TPU filament (smart materials FLEX). I employed a slim 3M double-sided adhesive to secure it to the frame. ...Not visually appealing, yet...

Ice scraper

After viewing a similar design, which required an external inline fan which I felt was too expensive and bulky, I designed this model. The original idea came from Doc Tanner at https://www.thingiverse.com/thing:2877754 if you want to checkout his. ...

I Need a Plate Support for My Magnetic Stirrer Container

With these shields in place, I'm confident that I can safely leave the resin inside the printer for an extended period without worrying about exposure to light. ...The 16 magnets I've employed have a 18mm diameter and 5mm height, but interestingly, the...

This design consists of 2 pieces which will be blended together when printed. 1. Import the files and insure that they are completly aligned 2. Turn one of the pieces off and slice individually (Make sure to Z-retract of at least 2.5mm. Do not...

This design was almost too straightforward, I actually considered omitting it from Thingiverse. To be honest, my printer's lid kept falling off whenever I opened it due to its tendency to swing all the way back. So, I decided to create a wedge...

Кронштейн для слива смолы с детали и стола после завершения печати. ...Наклоняет стол на 30 градусов, что позволяет стечь остаткам смолы

Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130

I designed this using Fusion 360, it's a neat little place for that useful spatula to be. the draining system may not be the best one, but it works, and it's certanly better than having the resin covered spatula over the desk. A small, nice looking...

Create parts for the 0815Paulchen at https://www.thingiverse.com/thing:3013054. The creation fits perfectly into a standard installation or insulation tube (flexible, outer diameter: 25mm, inner diameter 17.9mm). ... The airguide's outer diameter is...

I'm installing a ventilation system to clear out the stinky air from my space. ...The tube is connected to an exhaust hose that leads directly outside, drawing fresh air in and pushing stale odors out.

Extension for the homing bar to allow for a magnetic base.

A small shield for my second resin tank when it's not in use. ...As a lid, I employ the Thingiverse design 582131.

This is a guide for the build plate to properly square before locking it tight during Z calibration. Not all machine are the same set up, Guide may need some length adjustment. ...Please do modify if needed.

I created this using Fusion 360, a great little spot for the versatile spatula to reside. The draining system might not be perfect, but it functions and is definitely an improvement over having the resin-covered spatula cluttering up the desk. A...

Cover for Anycubic Photon Mono VAT to protect resin from UV, should be compatible with Elegoo Mars PRO Enjoy !

Spacer for the Z Limit switch on the AnyCubic Photon S when using the WhamBam Flex Plate system

Spacer for the Z Limit switch on the AnyCubic Photon S when using the WhamBam Flex Plate system

... on Thingiverse. Click this link to become part of the Photon Army: https://www.thingiverse.com/groups/anycubic-photon Watch this video for step-by-step instructions on how to clean your resin vat after printing: https://youtu.be/-9aPhhMv4ww

This flag is a replacement flag instead of using a spacer and longer screws when using a flex plate on the Anycubic Photon Mono X 6K.

I neded a holder for all the tools of my 3D printers (Anycubic predator, photon zero). So I designed one in Fusion360. ... Feel free to use.

Anycubic Photon S Drip Hanger Pro instead of an axis in the loops, you can put a piece of filament and glue it with glue

Anycubic Photon Side Panel 4-Inch Extraction Tube Adapter. ...The diameter has been upgraded to 9.6 inches for a more precise fit.