anycubic photon mono x fep 3d models

This is good for small failures where you might have something stuck to your FEP. Instructions: 1. Remove the bed plate. 2. Take an old support piece with a flat bottom and stick it in one of the corners flat side down. 3. Print this file. 4....

I liked IKE_144's remix of Ermai's build plate holder that makes it so you can angle your Anycubic Photon (or Qidi Shadow 5.5s in my case) build plate over the vat to help with dripping from different angles. My printer doesn't do bridges very...

This is good for small failures where you might have something stuck to your FEP. Instructions: Remove the bed plate. Take an old support piece with a flat bottom and stick it in one of the corners flat side down. Print this file. Remove the print...

SHOULD WORK WITH ANYCUBIC PHOTON S BUT HAS NOT BEEN TESTED FOR IT! ... INSTALLATION: 1) Unscrew the two screw under the plate mount in the front right corner 2) Insert the spacer between the metal plate and the plate mount 3) Retighten the two...

This device is designed to be attached to the Anycubic Photon, specifically aimed at reducing the smell from resin use.\r\nA brushless fan with an 80mm diameter should be installed between the panel and the box, secured in place using m5...

I made this little adapter so that I could use my Anycubic Photon build plate with the Elegoo Mercury Plus. It is a small quick design that can be quickly printer and used. It is designed to reuse the main bracket hardware that comes with Mercury...

Rear bulkhead of the Anycubic photon is a crucial component that requires precise installation. Two versions are available, one identical to the original and another adapted specifically for the ethernet connector. Key steps include preparing the...

This is designed for straining and collecting debris from anycubic photon vat systems. It can be particularly frustrating to go through the straining process after encountering failed prints, especially when the hardened resin is not visible at all...

My Anycubic Photon S has 2 exhaust fans in the rear of the build chamber. These exhaust fans have housings on top of them with small bags of activated carbon inside. This filter box is simply a container with holes in the bottom that are small enough...

@DocTanner crafted an innovative Rear Vent duct adapter for the Anycubic Photon, available here: https://www.myminifactory.com/object/3d-print-64661. I sought to enhance this design by adding a feature that would allow me to incorporate filters...

Full discloser: This filter system was made by  RJ Maker and here is his links, i just made an adapter to fit it on to the anycubic photon: Original files https://www.thingiverse.com/thing:1305485 and his youtube video that explains everything. The...

Earpiece X-Terra Monitor Single Channel

Vat cover for Anycubic MonoX 6k There are 4 file Cover Vat 6k is a complete cover for big printer (more or less 300mm) NO support needed The other 3 are the same cover but splitted for small printer (support needed) Attention: If you print the 3...

Vat cover for Anycubic MonoX 6k There are 4 file Cover Vat 6k is a complete cover for big printer (more or less 300mm) NO support needed The other 3 are the same cover but splitted for small printer (support needed) Attention: If you print the 3...

By setting the X-scale to around 70%, you can make it fit within the working area, although it will appear slightly narrower than the tray itself. ...The design underwent modifications in TinkerCAD and was shaped in 3D Studio Max before undergoing...

Here is the extractor/heater I have made for the Anycubic MONO. I wanted a design with a slim profile that can provide options to extract fume and heat resin caver for the best work temperature. All the plastic parts, should be printed using...

This is a remix of the other Easy-Bed level mods for the Anycubic Photon printer. The last version broke and deformed after a while, so i designed this version, that is a little bit sturdier and features threaded inserts for the Locking screws.One...

I tried to install a magflexplate system ( https://www.magflexplate.it/ ) on my Anycubic Photon D2. Problem was the system has an overall hight of 4,5 mm and the printer does not allow to set the zero parameter above the endpoint of the rail. The...

This is a custom-made adapter designed for using a 92mm fan in place of the rear panel on an Anycubic Photon 3D Printer. The main purpose of this adapter is to install an activated carbon filter element that draws fumes out of the printer through the...

Can be printed on the Photon M3 or any FDM printer. ... First generation, if there are any problems let me know.

8mm and 21mm spacers for 92x25mm and 92x38mm fans. ... I haven't printed these yet myself but you can print them on the Photon by printing it vertically.

... The connector fits relatively snuggly, but is not a perfect fit, so I advise using caution while setting it on the Z axis attachment. If not set securely, a large impact will cause it to drop off into the resin and potentially harm your FEP or LED.

You might also be interested in these topics: How to calibrate your exposure time: https://github.com/altLab/photon-resin-calibration?fbclid=IwAR06rlwNx4kWLCfTfY1CANumRgU0ohte1M7undZWjIbRVAB_O0DPgniykX8 And the Resin Curing Time Sheet Finder:...

Rework of the ELEGOO MARS Platform Stand for Magnetic Stirrer by giufini: https://www.thingiverse.com/thing:4193798 Allows you to mount the build platform of Photon 3D printer on top of a NEW OXO Good Grips POP Container - Airtight Food Storage - 4.4...

Made to use on the 3D Printer Resin Parts Washer https://www.thingiverse.com/thing:4462872 but will also work for ELEGOO MARS Platform Stand for Magnetic Stirrer by giufini https://www.thingiverse.com/thing:4193798 Bolt for Knob is a M6x30mm Hex...

If printing is complete，Use this will save resin Did a nice logo on the file added the .Photon file with supports :) remix from https://www.thingiverse.com/thing:2930511/files

Print the object with no centering ring directly onto the plate and the other with support using a printing service, specifically designed for use on a Photon S device.

i desing this angled cover inspired from @scottyujan desing but his was to big for my 3D Resin Printer so it's a smaller piece that works better for my Photon Zero printer. ... i suggest fliping the 3d model to a 90 degree angle for easier printing...

Remixed from https://www.thingiverse.com/thing:3671334 Specially designed for the latest Photon Zero resin printer, this updated model features smaller components, scaled down by 15% to fit perfectly on the new device. ...Additional stand extenders are...

Scale it to the Photon M3 Premium VAT dimensions. Split in two parts, for little printers. IMPORTANT: Due to different scaling values, depending on different slicers you have to calculate your own scale factor. ... As an example: I'm using prusa...