anycubic photon mono x vat 3d models

Replaces Photon Mono frame. ... Best results if layer height is .1-.2 mm, but still works with .3mm Works with original screws Tightens FEP film to allow for lower raised height (2-3mm)

Air vent box for ANYCUBIC PHOTON MONO SE using 3M Organic Vapor Cartridge 3311J-100-S1 and 12V Fan AV-F7530MB. You can swap the back panel of the printer with this. 12V can be drawn from the original fan cable inside of the printer. ...I added a DC/DC...

Air vent box for ANYCUBIC PHOTON MONO SE using 3M Organic Vapor Cartridge 3311J-100-S1 and 12V Fan AV-F7530MB. You can swap the back panel of the printer with this. 12V can be drawn from the original fan cable inside of the printer. ...I added a DC/DC...

Anycubic Photon Mono SE SPACER - Wham Bam + Two Trees Flex Plate Spacer Part for Endstop after adding the new magnetic BUILT Plate Here 3 Parts for : - Wham Bam 3,00 mm - Two Trees 2,75 mm (Ali Express) - No Namer 2,50 mm Print in PETG You need to...

Replace the FEP film for Anycubic Photon Mono (6.08 inch 2K), after modification, everything is normal and the cost is low. Preparation: Tools: 1. Electric drill 2. Screwdriver 3. M3 drill bit 4. Scissors 5. Wire cutter Material: ...

The rack grooves mate with half-cylinders inside the vat holder when the locking bolt is tightened down, so there is no sliding once the weight of the vat is present. The holder is angled forward by 5 degrees to prevent resin from dribbling under the...

This is a z stop extension plate for the new version of the Anycubic Photon Mono 4K 2022 version. There is no place to put a spacer on the new printer, so you must print an extension when installing a magnetic bed plate for homing purposes. I printed...

Here are my other designs for the Anycubic Mono X 4K ANYCUBIC Photon Mono X Clip On Heater Mount http://www.thingiverse.com/thing:5190198 ANYCUBIC Photon Mono X Z-Axis Bumper Guard http://www.thingiverse.com/thing:5185340 Anycubic Mono X Lid Spacer...

Please use the attached ZIP Files. ...The STL is only a place holder to upload the .ZIP File . Created from my original Stick delivered with my Anycubic Mono

Drip bracket for Anycubic Mono M5s Because of the very aggressive drip angle, if your print is too big, might not fit on the bracket. ...

The device for the printing platform of the 3-D printer Anycubic Photon Mono 2After printing, a large amount of photopolymer resin may remain on the part. To help the resin drain from the part, I developed this device.It is installed in place of the...

The Anycubic Photon Mono requires a z stop spacer to accommodate the thickness of the Wham Bam Flexible Build System. I created a spacer that goes between the z axis carriage and z stop metal tab that triggers the sensor to stop. The original...

Wham Bam's magnetic flex plate is awesome but adds 2.6mm to the height of the build plate. Unfortunately, there isn't enough play in the build plate mount so the Z stepper grinds when I home the plate. One option is to print a 2.6mm spacer but I...

I didn't want to wait on a Wham Bam plate because I had prints that needed to get done so I ordered the Sovol plates from Amazon. They had a slightly different height recommendation (2.7mm) so I remixed this adapter in Tinkercad. ...Not only were they...

This is a R_E_R_F test file for the Anycubic Photon Mono. All the ones I found out there took a while to run, so in the interest of saving time and resin, I created a R_E_R_F file that is heavily inspired by the ResinXP2-ValidationMatrix_200701...

This is a R_E_R_F test file for the Anycubic Photon Mono. All the ones I found out there took a while to run, so in the interest of saving time and resin, I created a R_E_R_F file that is heavily inspired by the ResinXP2-ValidationMatrix_200701, but...

Wide stand for better sustainability. ... I recommend using glue to connect all parts.

I created this sturdy support to increase the versatility of the tray's orientation and added pins to prevent the tower from disassembling unexpectedly. ...I also elevated a stage to adjust the overall height according to the size of the cans, providing...

I built the PTC heater for my Mono but I needed a clean way to run the wires out to the power supply. This is a minimal riser that has a 1" gap in the back to allow wires to pass through. You can improve the seal by adding foam, batting, hot glue,...

... made by goyetus. ... It uses: 3 x m3 Nuts. 3 x m3 x 12 16 Magnet 5x5x5 Changed the back plate to use this fan: https://es.aliexpress.com/item/32810655513.html?channel=twinner Added the step file to modify the back as you want.

... in place, and seal to the Vat. It uses the same philosophy as the Photon Mono X Vat. Watch the video below to see installation instructions. ... Installation Videohttps://youtu.be/mgY5Y1tznXI Mono X install (reference)https://youtu.be/tcCJFy_FcWE

By downloading User also acknowledges and understands the above and agrees to hold the creator harmless from any and all liability I printed in PETG and here are my settings: Machine: Ender Extender 400x400x500 Nozzle: 0.6 Layer height: 0.48 Line...

I wanted to get a magnetic build plate for my Photon Mono M5, but WhamBam only had it for the M5S. After a bit of research, and determining that the build plates are the same size, I decided to give it a try, and it seems to work perfectly with this...

Customized version of https://www.thingiverse.com/thing:3911914 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3911914

Designed this dropper to maximize volume and add double tilt.

Did you buy the most affordable SLA / resin printer? Did you discover the FEP film was incredibly difficult to replace without purchasing a costly pre-perforated FEP? I did. I designed this stencil to solve that problem. ...Simply use some paper...

refuerzo de paredes

2.5mm spacer for optical eye trigger arm for when you fit a magnetic bed. ...Not fancy, not a thing of beauty but does the job.

Thanks to @SnopSnapi for the excellent model and sharing the CAD.  I was  able to import and quickly add some countersunk holes for M3 fasteners to hold the lid more securely.I attached with M3x10 SHCS and M3 Locknuts on the inside of the lid/cover...

This is an adapter to tilt the build plate after the print to let trop off uncured resin.The V2 you can find here.