anycubic photon stl files 3d models

With the drip stand you can let the resin vat drip out in peace. All you need in addition is a 10mm thick rod (d=10mm r=5mm). ...I used a wooden stick and glued everything together with super glue.

Put the spacer on the aluminium pole and afterwards the draining bracket. You can leave the bracket on the pole during the print. ... Enjoy printing and if you got some question just text me and follow me instagram mail: 3dmodell.at@gmail.com ...

I embarked on this remix project because the M4 screws were slipping through my fingers, as their threads were only superficially printed.

I had some aluminum poles (2 of 200.30 mm and 2 of 100.40) so I made another stand for the vat holder that samuelemarazzita made.I modify the holder of the vat so the poles fit, the rest its my design, 2 M4 screws made the funnel base adjustable.

Guides the M3 front cover into location. Mounts off the existing back cover screws, using the original screws. Print two; it fits both sides. ...Print with supports.

I created a M5s VAT Cover & handle with 5mm small neodymium magnet holes. ... I also widen the screws hole on both sides, so that no need to unscrew to use the VAT cover

Small tool holder without any particular fixation, allowing to hold a spatula as well as a BTR/Allen wrench to adjust the plate. Also allows to limit the scratches on the anti-UV cover Small tool holder without special fixing, allowing to hold a...

The original design has two problem: Hardware parts are not so common (no M4 inserts, and no M6x30 required ) and you must use a tool to secure screws (tight space to operate)... My remix is more convenient in hardware parts and friendly use (no...

A Revolutionary Scent-Free Tower: Empowering a Fresh Environment with Active Carbon and Joyful Printing

The part fixes the build plate at a steep angle for good resin runoff.

I'm glad we're on the same page. ...Thank you so much, that means a lot to me!

The headspace for the fan in the original was too small and prevented the fan from operating well, resulting in overheating and the fan shutting down. This lid allows the fan to operate properly. ...

Additional handle for wash & cure machine. It allows you to conveniently open the machine with one hand and reduces the dirt on the cover. ... The handle should be glued with double-sided tape.

Works perfectly so far , printing for 7 hours in a completely sealed room with minimal odor buildup.\r\nSimply pop off the top of the filter cartridge, snap on the replacement part, then attach it securely to the rear vent.\r\nI printed this item...

this is a remix thing:2877754 it just includes space for a computer fan 92x92

The curved top portion of the build plate may be not really accurate, but the rest seems to be OK.

I looked for a drip bracket on thingiverse and did not find one so I made one myself with help from a friend. The fit on the lift mechanism is quite tight I would maybe shave of 0.5mm off from one of the long inside parts. But some sanding did the...

This is a simple bracket for holding the build plate at a slight angle so that the resin can drain away more easily after a print.

<p>Améliore le filtre à charbon où l'on peut mettre du charbon en grains ou en billes ou filtre à charbon de hotte aspirante de Cuisine ou pour aquarium</p> <p>Pour cela le charbon filtre très bien les odeurs</p> <h3>Print Settings</h3>...

This desgin works together the blue cover no collision. For assembly the Airpure left and right you need M3 screew and mother. Print with a FDM printer If there any problems let me know. ... Happy printing!!!

For top and bottom print two pieces, also you need 4 x M3 screews. ...

This bracket holds the build plate vertically over the vat, tilted slightly forward and inward to recover resin drip at one corner.

This is my odor extraction system with a powerful 120x120 fan and spiral pipe. No permanent modifications are necessary; you won't need to drill holes in the printer. I utilize a Sunon PMD1212PMB1-A fan, which is the most powerful one I've...

Air-Filter Resin Printer Anicubic Mono X Other components: Filter mat (universal micro filter cotton) Activated charcoal (granulated activated charcoal) Cooling Fan (Ronyaoko 5V 0.25A 80mm 80x10mm 8cm Brushless DC USB Connector) The filter...

This is a revised version of the platform bracket provided by Elegoo. It helps a lot when removing the model from the build platform because it allows the resin to flow into the tank. Just unscrew the platform from the holder, insert the "Platform...

Updated 9/6/2019 (See Below) I love the original, but went a different direction, so made some (very) simple mods: 1. The filter box is only 9mm thickness to accommodate thinner filters. I just cut them in Prusalicer, but they work. 2. The screw...

I created this sturdy support to increase the versatility of the tray's orientation and added pins to prevent the tower from disassembling unexpectedly. ...I also elevated a stage to adjust the overall height according to the size of the cans, providing...

These feet will fit perfectly in the oval recess of the printer. Print them in TPU and it will keep the printer from sliding so easily and reduce some vibration. Use you Z axis scaling to print them as tall as you like. For example, My printer was...