anycubic predator enclosure 3d models

A simple LCD and 7 inch Display Frame. You just need some M3 screws, M5x8, 4 x M5x12 and a longer one who connects the backplate and the hinges. And of course some washers, nuts.... the basic stuff. ... The LCD Frame is a remix: ...

Необходимые метизы на три каретки: винт м5х20 - 12шт. ( есть две версии верхней части каретки под потай и под любой, если болт потай то достаточно длины 20 если обычный то 20 мало а 25 много придется подкладывать 2мм шайбы м5) винт м4х20 - 6шт.

40x6mm https://www.roboter-bausatz.de/p/carbon-rohr-40-cm 6x12mm Magnets https://www.ebay.de/itm/200817005980 can be glued with epoxy, maybe even superglue works. rod lenght should be around 445mm - but i recommend measure it by yourself I...

This one is a remix of my initial fixing idea for a tool holder and ThinkAndBuild's awesome contribution. Compared to ThinkAndBuild's version, it introduces a new mechanism to secure the tool holder directly onto the printer. Unlike their design,...

This is my level test because I was unhappy with the one I found. It features a diameter of 360mm, which fits perfectly on the print bed. I created two versions: a 0.2mm design that uses 1g of filament and a 0.4mm version that requires 2g of...

The rattle from the existing blower unit is becoming too intense! We're aware that the blower was smaller, but noise was amplified - it's time to switch out the amplifier for a more substantial unit. I propose we opt for a 70mm fan as our maximum...

Remixed from https://www.thingiverse.com/thing:3995663 And you need use front plate from https://www.thingiverse.com/thing:2368534

It's the same system found on the internet, but instead of putting pressure in the metallic area which breaks, this system takes all the metallic part and a piece of the arm as well. It also has holes to place springs or rubber pieces. There are two...

Hello again folks.... Here is the TFT70 version of my slotted panel adapter. Please try to use 0.4 nozzle as some details start to go funky! May require sanding to make the slot work, but before anyone moans, I printed at 0.2 layer and didn't...

Following the many problems of the original V5-j hotend, I decided to create an effector compatible with 24V MK8 type hotends. It works perfectly on my printer, with a Noctua NF-A4x20 and two 4010 fans. You will only need a few M3 screws to install...

I was searching for a reliable driver cooling solution. Since the original setup was too loud and the Noctua fan wasn't strong enough, I came up with an innovative idea to incorporate a large fan into the lid. So I designed this custom housing and...

As I receive the tools with the printer, I had to think on my feet and come up with a solution for storing them in an easily accessible way. In a bit of a rush, I quickly came up with this idea. So far, it's been working out well - I used the no-tabs...

Three pre-fabricated panels need to be installed around the build plate. One panel serves as a simple plane, while another features an opening specifically designed for the heated bed cable to pass through. The third panel boasts a rectangular hole...

A breeze to print a fan duct with wide open airflow available immediately. Prints in two parts, eliminating the need for supports entirely. Bottomside prints upside down, of course, as required. A spacer has been added, allowing insertion between the...

Following the many problems of the original V5-j hotend, I decided to create an effector compatible with 24V MK8 type hotends. It works perfectly on my printer, with a Noctua NF-A4x20 and two 4010 fans. You will only need a few M3 screws to install...

A versatile base plate for all three legs of a 3D printer. ...Adding some bouncy rubber balls beneath each leg helps create a flexible support system that yields cleaner prints, particularly when printing rapidly.

I neded a holder for all the tools of my 3D printers (Anycubic predator, photon zero). So I designed one in Fusion360. ... Feel free to use.

This is a clip connecting Mosaic Palette 2 to Anycubic Predator. ... 02.02.20 - uploaded a complete setup, get it here: https://www.thingiverse.com/thing:4140259

A high-performance thermal management system featuring an enhanced E3D hotend paired with a standard issue Anycubic Predator effector in a striking blue hue.

This video demonstrates how to connect the Mosaic Palette 2 to the Anycubic Predator. ... 02.02.20 - A full setup is now available, check it out at https://www.thingiverse.com/thing:4140259

A Simple Upgrade Solution: Mounting the BIGTREETECH SKR V1.3 in the AnyCubic Predator D. The AnyCubic Predator D is a great printer, but it's not without its flaws. One major weakness is the Trigorilla Pro mainboard, which can be frustrating to work...

... of the original Smarteffector PCB Board. One version includes flying extruder holes, while the other does not. This is my carriage adapter designed specifically for Hayden Huntley's magball Rod. The printer in question is the Anycubic Predator.

Mount for a BMG/Bondtech or clone style extruder and stepper motor on an Anycubic Predator. Retains flying/sprung style design for those who want it. M4 bolts/nuts and a washer for fasteners. ...I printed mine in PCTG (Polycarbonate-PETG blend) however...

I discovered that the spool holder on my Anycubic Predator Delta printer had become quite noisy, so I took matters into my own hands by creating a custom pad to reduce friction and provide a silky-smooth surface for the filament spool to rest...

Changes Implemented: * Swapped out the mount to accommodate a non-standard LCD screen, replacing the stock LCD of the Anycubic Predator * Created additional space for integration with the PanelDue board * Upgraded the ribbon cable to 10 ways,...

Anycubic Predator Carriage Adapter for Haydn Magball Arms (Remix) ==================================================== Description ------------- I take an existing carriage adapter designed by Haydn Huntley, originally intended for the Anycubic...

... to put the panel quickly and that is practical, do not expect a beautiful design ... ...Print Settings Printer Brand: Anycubic Printer: Predator Rafts: No Supports: Yes Resolution: 0.2 Infill: 35 Filament: Sunlu Pla White Category: 3D Printer Parts

Do not use this, I had to recalibrate my Anycubic Predator and then the original from https://www.thingiverse.com/thing:4441076 is perfect for the Turmberg3D - Hotend Set , bigger hole for the heatsink is nessisary...

This is a plug i created for the Anycubic Predator top cover. In the top cover is a very big hole for the bowden tube. It always bothered me just simply from the looks of it. But i also dicovered that a lot of dust and dirt gets in there if you dont...

Predator