anycubic vyper extruder 3d models

Here's a simple spool support I created in Fusion 360. I didn't like how the spool holder would twist and sag, causing the filament reel to slide over and look like it would fall off. The support is easy to install and remove and keeps the spool...

Remix to fit https://www.thingiverse.com/thing:4977520

Hi all, this is my first designed Thingi, based on https://www.thingiverse.com/thing:4942227 You need 5x 5mm cable ties for mounting the cable at the holder. Feel free to use, give me feedback pls. ...Ty.

Helps reduce Vibration on Spool holder

Schutzkappen für die beiden oberen Ecken der Z-Achsen. Schutz vor Staub und Beschädigung. Gedruckt mit TPU, aber andere Materialien sollten auch passen. Der Entwurf ist so gestaltet, dass es locker sitzt. Automatic translation into English ...

i don't know much about 3d design but i tried my best to make this because the other ones i found either didn't fit right or the grip was too loose or so tight it squished the tube. ... my sensor still lights up when the printer goes to the far...

Un petit support pour metttre un rpi qui heberge octoprint ou astroprint. ... Passe juste sous le plateau, donc ca prends pas de place !

This is an improvement version of @taka0909 and already asked him for the credit. There may be some problems in the original designs like the arm is not strong enough and the part is a bit conflict with the lower platform. Also, to make it easier...

Just a stand to hold the hotend for doing any maintenance. So it can be removed from the strain gauge. ... it should have its back on the bed for printing

Ein Halter passend für den Rollenhalter https://www.thingiverse.com/thing:5568622/files Zur Befestigung habe ich diese T-nut Stücke verwendet. (3 Stück) https://www.thingiverse.com/thing:3050607 Für einen sauberen Filamenteinzug, in jeder...

- 10% infill, you may want to increase this if you'd like the slider cover to block more lights - I used tree support for the case

Remixed arm for 1/4" screw hole for cameras. Check the original thingiverse for the mount and pin. ...Might make a horizonal version later on.

Print in PETG or ABS. 100%infill. Layerhöhe geht auch bei 0,2. ... 350ohm DMS vorhandene Kabel vom alten Sensor, oder neue Molex 1,25 mit 4 Pins.

I couldn't fine a good mount for my webcam to use with octoprint, so I made my own.Print SettingsPrinter Brand:AnycubicPrinter: VyperRafts:NoSupports: NoResolution:0.15mmInfill: 15% GyroidFilament: eSun PLA+ Black   Category: 3D Printer Accessories

you need 2 x M3 14mm and 2 x M3 6mm and 4 x lock nut have been printing with it for a week now, and it is still working fine

I couldn't fine a good mount for my webcam to use with octoprint, so I made my own.

- 10% infill, you may want to increase this for the slider if you want it to block more screen lights.- I used tree support for the case - Recommend to use 0.2mm resolution

Hallo, hier mein Entwurf zum einbau eine Noctua 80x80x25 Lüfter 12 Volt mit Stepp Down Ich habe es noch nicht selber gedruckt aber es sollte passen. Benütigt wird: 1x 80x80x25 Lüfter (Noctua 12 Volt) 1x Stepp Down 24 auf 12 Volt 4x M3x16...

Lampholder for dual 5015 Printhead.

Hi this is my first Thing ;-) So have grace with me... ... It is a Camer holder for the Raspberry Pi it can move in all directions Instruction: You need to glue Part 2 and 3 thogeter (may change in future) And for the rest Flathead Screws 4x M4...

<p><strong>Hello,</strong></p><p>this is a small upgrade that the z-axis is holding in the z-axis guide without Wobbling.<br>its easy to print and you can you how good your printer is calibrated :-D</p><p>make it first over the Bearing and than in...

print it up side to Bed , maybe on an Glass surface. ... Enjoy

Mount for an RaspberryPi Camera

UPDATE: I separated the pin and the back part. I also redesigned the back part a bit, so it won't fall off easily. ---- Because I was annoyed with the need to use cable ties each time for holding the printhead-cable in place (and i ran out of...

Resized model.

# If you Made it, # # Put your Photo on "Makes" section. # ## Italiano: ## Coperchio per i v-slot telaio della stamapante. Incastro facile sia dentro che fuori. Puoi utilizzare lo slicer per impostare una lunghezza, per esempio io li ho...

Klammer für das Kabel und den Bowdenzug

This a small upgrade that can help you avoid filament detector problems. ...Easy mounted without any screws and glue.

Recording changed so that you can insert the role from the front.

<p>The drawing is in mm.&nbsp;</p><p>&nbsp;</p><p>Link to LED lights. ...&nbsp;</p><p>https://www.aliexpress.com/item/1005004068826654.html?spm=a2g0o.order_list.0.0.333d1802cZag1u</p>