aperture science website 3d models
47812 3d models found related to aperture science website.thingiverse
This Keychain resembles the logo of Aperture Science and the logo of Aperture Science Innovators from the game series Portal.
thingiverse
First 3d model i made. ... basically just a coin with the aperture science logo on it.
thingiverse
Aperture Science logo Modeled With FreeCAD Print Settings Printer: FlashForge Creator Pro Rafts: Doesn't Matter Supports: No Resolution: 0.10 Infill: 20 %
thingiverse
A pencil pot, inspired by the #WaveyWednesday hashtag on Twitter - this time remixing the Aperture Science logo into a twisty vase thingy.
thingiverse
... actually keep drinks off my desk so I don't have to clean it as often. ...So I used my Aperture Science Testing Printer and made this. Instructions I subtracted an Aperture Science logo from a disc with a raised lip. ...Printed on a Rigidbot Big.
thingiverse
An Aperture Science coaster. Print and enjoy. PLA should hold up, seeing as your cups aren't burning your hands daily. ... Scale X/Y (Non-uniform) to a desired diameter if needed.
myminifactory
This knob decal was found on Cults3D and Thingiverse, made by DJPOSTKA. ...The link to the actual page can be found below: https://cults3d.com/en/3d-model/home/ender-3-aperture-science-knob-portal
thingiverse
Next thing for Portal and Portal 2 fans Aperture science mug. Just glue to mug handle and drink your coffee. Sorry I had to repair the model because of before E in the word laboratories looked life I after slicing. ...
cults3d
This is the Aperture Science logo, featured in the Portal games made by Valve. Modeled by me, optimized for printing. ... Portal and it's logo is respective property of Valve inc.
prusaprinters
Three full cubes, one with Aperture Science logo, one Companion Cube (with the heart logo) and a blank template without a logo. ...The fourth file contains both the Science and Companion cubes, cut in half (to be glued) to print without support. Some of...
thingiverse
I recreated the Aperture Science logo in FreeCAD and made it into this coaster. Change filament 1/2 way up for the two-tone effect. Sorry for the bad quality on the top layer in the photo. ...Not sure if it was printer glitch or if it's just that...
thingiverse
For a projection, I just made a cover with an Aperture Science logo-shaped hole, and the hole that goes over the cylinder on the flashlight to keep it on has a friction fit with a diameter of just over 4 mm. ...Inside the flashlight, I have a switch...
thingiverse
A drink coaster with the Aperture Science logo. This prints in two pieces: The main coaster and the insert chips. I printed the chips in white and painted them, then glued them in place on the coaster. The blue/orange chips are made slightly smaller...
thingiverse
I wanted an Aperture Science logo as my extruder visualizer, so I made one. Glue a round 8 x 3 mm magnet to the back and it'll stick to the back of your extruder NEMA motor's shaft. There's a small circle on the back to help you get the magnet...
thingiverse
This is the Aperture Science logo, featured in the Portal games made by Valve. Modeled by me, optimized for printing. Portal and it's logo is respective property of Valve inc. Instructions This logo...
thingiverse
Don't you think the **Aperture Science** logo looks pretty cool? Me too! This is a fun and interesting little trinket to add to your shoes if you're a fan of the *Portal* series, it's the perfect little print and addition to your shoes to express...
thingiverse
I wanted to make an extruder spinner because I thought they were fun and thought "Why not Aperture Science?" I printed at .3 layer height with supports. It's kind of a waste of material for the supports but I didn't try to optimize it at all. May...
thingiverse
Aperture Science Drinks Coaster. Made in Fusion 360. This is my first CAD model so go easy, though any constructive feedback is welcome. I reduced the X and Y size to 85mm for the print in the photos so this does scale well, though it's...
grabcad
One of the 'vintage' Aperture logos from the game Portal 2.
thingiverse
This is yet another spool for earbuds :) Inspired by Portal 2 Aperture Sciense Labs
thingiverse
Aperture Laboratories investment opportunity #5: The aperture coaster. The most scientific drink coaster ever made! For use on your desk or any other table in existance. Depending on the material you choose to print with, you can use it for hot or...
pinshape
This Keychain Dangler resembles the logo of Aperture Science from the game series Portal. ...(Dimensions: 30.02mm x 106.5mm x 4mm) Old Aperture (Aperture Innovators) Version NOW Available.
thingiverse
Finally an aperture science calibration cube! ...