apm copter 3d models
2439 3d models found related to apm copter.thingiverse
My build is as follows: one Quad Bottom one Quad Base Top four Landing Gear Arms four Quad Arms (motor mounts) one Battery Strap Base Four ST2210 motors Four 8045 props One Qbrain 4x20 ESC APM 2.5+ w/ GPS and power sensor 900Mhz Telemetry Module...
thingiverse
A mounting plate to put your APM on and mount it on a Tarrot 820 Hexacopter along with its cover, Holes have been made on the underside to accommodate the screw heads. I recommend attaching it to the plate with strong VHB double sided tape. ...Print...
thingiverse
My concept is that I wanted an anti-vibration mount for my APM 2.5, although this should work for any controller, where I could easily attach and detach modules between multicopters. I'm currently only using one mount, but plan on making more. I...
thingiverse
... to add the 4mm cylinder. ... The rod is 7 cm high and can be easily cut to adjust the length you need. I advise to let 3/4 cm which is a quite good length. The base could be attached with 2 rilsan collars to the leg of the copter. ...
thingiverse
This is a custom mounting plate with embedded case for a APM 2.5/2.6 flight controller. Has two wings on the side for the telemetry module and receiver module. Instructions Printed with 3 shells at...
thingiverse
multifunctional copter at the moment I lay out the support racks of the motors and the frame of the copter https://vimeo.com/817928972
thingiverse
Copter found in the spaces of the Internet in a format * .dxf. I just adapted it for CorelDRAW. Closed loop and all that ... All four screws rotate independently. Very interesting, spectacular and complex model for the assembly. Red circuit - for a...
thingiverse
Customized version of https://www.thingiverse.com/thing:4439787 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4439787
thingiverse
APM cover with openings for old styled GPS port and USB connection. No additional support structures required for printing, the openings are designed with support structures and it's easily removed. This APM cover is part of my Spyda 500 design...
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: stick_width = 8 message = APM font_thickness = 5 stick_thickness = 2 flat_bottom = 2 hole_radius = 3 Font = write/Letters.dxf font_size = 8
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=88476 Instructions Using the following options: collar_stay_height = 10 image_file = collar_stay20141208-11979-e6dm40-0.dat text = APM font = write/Letters.dxf build_plate_selector = 2 gap_y = 2...
thingiverse
My things: APM 2.6 http://store.3drobotics.com/products/apm-2-6-kit-1 Telemetry http://store.3drobotics.com/products/3dr-radio-telemetry-kit-433-mhz Minim OSD http://store.3drobotics.com/products/apm-minimosd-rev-1-1 FatShark AttitudeS...
thingiverse
Cover to protect APM from sun and dust, fits directly above the APM plate that I have also uploaded here.
thingiverse
Bridge to mount apm on HK FPV250. ... Use small washers and servo screws to mount.
grabcad
details here: http://diydrones.com/profiles/blogs/apm-mode-switch-with-lcd-display
thingiverse
This is a simple mounting strap for the APM flight controllers. It holds the APM down firmly. Holes are for M3 screws. ...Enjoy, and don't forget to post your makes!