apple tv first gen 3d models
228010 3d models found related to apple tv first gen.thingiverse
This is a 1:1 replica of the Apple TV. ...I will be adding a remote to the model files soon!
thingiverse
If you need a base for your apple pencil while you're at your desk, this gadget is for you.
cults3d
If you need a base for your apple pencil while you're at your desk, this gadget is for you. ... The .zip file contains two versions, whit and whitout logo extruded.
pinshape
Apple TV GEN 4 Cradle. The picture shows it installed upside down. This was for a test fitting, and it fits pretty snug. Using it to mount to the back of my LG Oled tv to hide the wires and create a nicer set up. Works like a charm! Modeled in Fusion...
myminifactory
This stand will make your Apple TV box sit 1 inch higher. ...The inside is hollow so it uses very little filament.
thingiverse
... the original tabs broke for me (could be my cheap PLA and lack of printing skill). Added hanging tab in back of model to work with my TV mount as the VESA holes were already used. ... Because of this tab, supports are probably needed when printing.
thingiverse
Apple TV 4th gen remote wall mount. ... Print standing up.
thingiverse
Mount for you apple tv (4k gen 3 (95mm x 30mm)) to attach to your TV bracket behind the TV.
thingiverse
This is a holder designed to hold the NEW Apple TV released in October 2015. ...This may effect the wifi signal so i recommend using ethernet
thingiverse
Visit this page to identify which generation Apple TV you have:https://support.apple.com/en-ca/HT200008 File Version History: Apple TV (4th Gen) Remote Holder Version 02.stl First version of the file uploaded File includes the actual Apple TV remote...
prusaprinters
A work-in-progress wall mount for the 4th Gen Apple TV. ...There are openings on each side to allow the Apple TV to be oriented in any direction. Category: Household
thingiverse
A work-in-progress wall mount for the 4th Gen Apple TV. ...There are openings on each side to allow the Apple TV to be oriented in any direction.
thingiverse
Apple TV 3rd Gen Wall Mount, print in parts will require glue the two parts, top, and bottom. ... Recommendation: 1) Install bottom part to the wall 2) Glue the top part to the bottom or base when is fixed to the wall
thingiverse
Here's a simple holder for my Apple TV Gen 4 remote. I've screwed my remotes into the side of a small pine Ikea coffee table. Attaches with a single 4G screw. You could use the 3M command tape to attach to a smooth surface, but it didn't...
thingiverse
This is a Wall mount for the Apple TV from the first generation! Opening in the Bottom will give you the possibility to turn it 180 deg around so you can let come the cables out there! 123d Design file attached, so you can change it to your needs! ... ...
thingiverse
I needed a cradle to hold an Apple TV on the back of our rolling carts so rather than using one with screw mounts, I designed one with a slip on tab. Designed to fit the AppleTV 4th Gen. The spacing for the rear tab is about 2mm, so it should fit...
thingiverse
mount for apple tv 4k wifi 3rd generation (no ethernet cable) https://www.amazon.com/Apple-2022-Wi%E2%80%91Fi-Storage-Generation/dp/B0BJLDVJTC fit is snug, has a hole on the bottom to bolt to whatever you please, or screw onto your tv's vesa mounting...
thingiverse
Wall mount for the Remote of the Apple TV 3rd Generation. The Remote is tilted in an Angle of around 15° what makes it easier to grab the remote. ...Print Settings Printer Brand: RepRap ...
thingiverse
I designed this nifty apple remote holder because I keep losing mine in the couch. Thanks, Apple. It gives the remote a little bit more of an ergonomic grip and some bulk to make sure it doesn't slip into unwanted spaces. ... The tolerances are...
thingiverse
Remix of Apple TV Remote holder (Gen 4) by gronax www.thingiverse.com/thing:3601985 W/ Apple logo
thingiverse
Spacer that makes a 2nd or 3rd Gen Apple TV wide enough to lock into a mount made for an 4K Apple TV.
thingiverse
Remote control holders including Apple TV remotes (4th and 5th Generation). I added a slit to allow vertical as well as slanted storage for the Apple TV remote. No support is needed. ... The 5th Gen stands are coming.
thingiverse
I updated this design to fit the Apple TV 4K 2nd Gen 2021 remote. ...I also angled the hole for the remote.
thingiverse
The stl file is to suit a 4th-gen Apple TV. The SCAD file is customisable to be used for many small devices - I also used is for a small network switch that I also stuff behind the TV. Let me know if you would like changes or download the...
thingiverse
Remixed from: https://www.thingiverse.com/thing:244777 https://www.thingiverse.com/thing:4642211 Remixed this one to fit the Apple TV 4th Gen and 4k models. ...I used the no supports version to make it easy to print
cults3d
Included in this download you will find: Sturdy and easy to print Apple TV Craddle Works with Airport Express & Apple TV 2nd & 3rd gen. ...Mount it with nails or double sided tape If you like this you might want to take a look at my other...
thingiverse
This case is specifically for the Apple TV Siri Remote (2nd gen). - Designed to be printed with **TPU filament** - Designed to be **printed upright** with **no raft or supports** There are 3 designs included: 1. case with airtag -- this is...
pinshape
Ever needed to have your Airport Express or Apple TV (2nd 3rd gen) hanging from a wall to save space or just to keep it out of the way? If you say yes then just download this model and print it yourself or ask a friend to print it for you, clean...