apple tv holder 3d print

Quick Write-up: nicholasgiovinco.com/nicholasgiovinco/2012/6/29/thingiverse-creation-apple-tv-remote-holder.html Update 2: I've plugged the suspected hole which seems to trouble some people. Update 1: I've uploaded a *fixed* version, which should...

iPhone X Cell phone holder Apple Logo TV The largest part is 14cm. ...Please refer to 3d printing bad size

apple TV holder

apple TV holder

vErY GoOd Tv ApPLe HOldEr

This remote holder works with the old Apple TV and the new Apple TV remote. It holds it so it will not slip! ...Enjoy and take a look at my other things to print!

An apple TV holder with a clip to attach to the poles that hold projectors

A full-size remote control holder for a current model Apple TV Siri Remote. Depending on your print settings, this might be a little tight, working on the tolerances. I was tired of the Apple TV remote falling between the couch cushions, getting...

Appe Tv Holder

This is my model of an apple tv remote Holder, which you can stick to a wall with double-sided adhesive tape.

This is a remix of the single remote holder by markbajaj. ...I filled in the internal cavity and removed the Apple TV text.

Simple apple tv remote holder. I printed it standing up and the bridge at the front opening came out ok with no support. Some double sided sticky tape to mount it and never lose your remote again!! ... Unless you forget to put it in the holder 8)

This remote holder works with the Apple TV gen 1, 2 , 3 and 4 remote. Enjoy and check out my other models to print! Instructions I printed mine with 25% infill for a little extra weight, and 0.2 mm layer thickness. ...Enjoy!

This Apple TV Remote Holder works with all generation Apply TV remotes. (Yes, even the new one.) This is great if you keep losing it in the couch and wish it could stand up. It is not too tippable, you have to really hit it hard to get it to tip!

This is a 3-D printed holder for your apple tv box. There are two small holes on either side of the box, visible in the pictures, and you can use to screw nails throw so that your apple tv will stay to the wall. ... I did make one error that is...

... your Apple tv remote again! ...This remote holder has a snug fit with the remote to allow easy use of the remote while making sure the remote doesn't slip between the couch cushions.Print SettingsRafts: YesSupports: NoResolution: .2 mmInfill: 5-10%

Never lose your Apple tv remote again! This remote holder has a snug fit with the remote to allow easy use of the remote while making sure the remote doesn't slip between the couch cushions. ...Print Settings Rafts: Yes Supports: No Resolution: .2 mm...

Simple Apple TV remote deck. ...No supports needed

I made this Apple TV 4K remote holder. This was actually my very first project that I did all on my own. I made this in Tinkercad. Now this is made for my Apple TV remote which is a Apple TV 4K and it has a little white ring around the menu...

An Apple TV holder with a slot in the rear for cords. The hole in the top is designed to fit a bolt or screw to attach to the underside of a desk or even a wall. ...Print Settings Printer Brand: LulzBot Printer: TAZ 6 Rafts: Doesn't Matter Supports:...

The Apple TV remote is a pain to use. This add on gives it  some weight and size so its easier to grip.Print with with opening down and support. Also add a modifier to the bottom half of the holder and raise the infill to 90% to get a nice heft...

Apple TV holder, I designed it for the 4th and 5th generation (the 3rd generation is 10mm thinner). On the back there are 2 holes with countersinks around the bracket with 2 3.5mm Spax screws on e.g. to screw a cabinet. Apple TV Halterung, Die...

Just a simple apple watch remote holder :) :)

It holds a Apple Tv and requires screws to go in the wall to hang

Designed and printed it to hang the Apple TV on the wall. Part 1 is hold the Apple TV itself and part 2 is to "close it" as a lid, so it can't be stolen. There are 3 holes which have a diameter of 4mm. I have added the Fusion 360 Design file.

Good size / Bonnes dimensions Support pour télécommande d'Apple TV, design et pratique. ...V5 checked size (on Solidworks Software) I apologize for troubles on previous versions Print Settings Printer Brand: RepRap Printer: Vertex K8400 Rafts: Doesn't...

This product is used to hold up an apple TV. This is only a prototype so there are some flaws. ...The back opening is too small and if printed you will need to open it up about a 1/4 of an inch more.

Quick Write-up: http://www.nicholasgiovinco.com/nicholasgiovinco/2012/6/29/thingiverse-creation-apple-tv-remote-holder.html Update 2: I've plugged the suspected hole which seems to trouble some people. Update 1: I've uploaded a fixed version, which...

This is a remix of the Duel remote stand by Cookie1. ...I filled out the first hole and put Apple TV text in it.

Just a prototype but works and can hold apple tv. ...Only problem is that the cord is to stiff and does not bend when put on the wall.