aps film scanner 3d models
34778 3d models found related to aps film scanner.thingiverse
This is a holder for scanning analog APS film (24 mm wide) on a flatbed scanner (it is designed to work with an Epson V700 and similar models (10 mm between the glass surfaces)). Instructions: The end piece has to be mirrored and printed twice. ...
thingiverse
My design of a adapter to fit APS-film in a film scanner. Easy montage Use settings for 126 film and EV+1. ...Then cut out white edges.
prusaprinters
The round corner is on the lower left side.Open your APS cartridge carefully and get out the beginning of the filmSlide the film in the adapter from the right side until it comes out on the leftInsert the adapter with the film in your x33-Scan film...
thingiverse
A film holder for scanning APS negatives. ... This is a Remix from : https://www.thingiverse.com/thing:4741606
thingiverse
One tool is a key for the APS film gate door, to open/close it. I've found that the door opens and closes much easier if you first set the canister's "stage" to "3" (look at the end of the can). Be gentle when using the key tool, as it is semi...
prusaprinters
There are two tools and a shiv/joiner to keeping the tools together so you are less likely to loose 'em.One tool is a key for the APS film gate door, to open/close it. I've found that the door opens and closes much easier if you first set the...
thingiverse
This adapter allows you to use APS film in most 35mm cameras. The spacer will make the film centered. The adapter also allows for rewind (very important!). Note: this will not work in most electronic rewind cameras, such as Yashica 200AF. It simply...
cults3d
35mm film scanner made of resin, to scan the entire film. ...4 magnets 5x2mm are needed
myminifactory
Please find the detail at hackaday.io With this scanner you can make digital copies of your 8mm film.
thingiverse
Film holder (135 format) for scanner. Used with an Epson V600 but I think it fits with all flatbed scanners. Designed for strips of 6 frames (can load 5 frames). The film is stretched over its length and width to avoid a curved shape. ... It allows...
thingiverse
... of 127 film, the other for a strip of four 126 frames. These are old formats and many flatbed scanners don't come with adapters for them. ...The design is imperfect as it has nothing to stop the negatives from curling, but will work in some cases.
thingiverse
This scanner has 4 parts: 1. ... The base unit 2. Film slider (purchased from B&H Pacific Image 35mm Film Holder) 3. Hood to mount DSLR (Canon DSLR + EF100mm f/2.8L Lens with hood) 4. Any LED light box with uniform lighting. ...
thingiverse
Please look on new revision of 35mm film scanner/digitizer: https://www.thingiverse.com/thing:4607011 It is tool for digitizing 35mm analog films. I`m using Sony A7II with 26mm macro rings (10+16) and Samyang AF 35/1.4. ...As a backlight I`m using...
thingiverse
This is a set of parts that can be used to build a 8mm film scanner. It uses any SLR camera that has a remote jack (usually a 2.5mm plug) to allow for remote shooting. The film movement is governed by an Arduino that runs two servos for film...
thingiverse
The frame keeps the print from being smashed against the glass (which minimizes the change of getting rainbows when scanning) and helps align the image to the scanner edge. ...The dots are to help with bed adhesion; break those off at the end of the...
thingiverse
Uploaded for a reddit user Measures 35mm between pins Adjust flow rate after each print so you can get it just right so they hold together and keep the film in place Try scanning from both sides to see which one is more clear.
thingiverse
... or set the delay to 5 seconds, that way the camera isn't moved by your hand while the shutter fires. To change frames, open the holder, slide the film over, close it back down, and position it under the tube, use a true macro lens for best results.
thingiverse
This black box is intended to scan 35mm width film using mobile phone camera. Make sure your phone camera focuses well on 50mm distance from object. BOM: -Light source: 7W white LED:...
prusaprinters
Uploaded for a reddit user Measures 35mm between pins Adjust flow rate after each print so you can get it just right so they hold together and keep the film in place Try scanning from both sides to see which one is more clear. Print Settings Printer...
thingiverse
This is a simple adapter for APS films for the Reflecta x33-Scan film scanner. ** IMPORTANT: ** You absolutely need to print this with transparent filament. See [this artcile on my...
thingiverse
I shoot and home-develop a lot of different film formats, and less-standard film development reels (like APS) are hard to come by, and expensive AF when they do creep onto the market. So.... I made my own. This one is designed to work in a Paterson...
prusaprinters
I shoot and home-develop a lot of different film formats, and less-standard film development reels (like APS) are hard to come by, and expensive AF when they do creep onto the market. So.... I made my own. This one is designed to work in a Paterson...
prusaprinters
Oh, and if you are looking at this, I'm sure you've realized that APS film canisters are very different too, so I also designed a set of "APS Canister Tools" that can be used to open the film gate and wind/unwind the film from the can. Check out my...
thingiverse
... film scanner and allows you to use a phone fitted with a siriui macro lens mounted to a Moment case. With those items mounted to my Pixel 2XL, and this print attached to the base of the lomography film scanner, I am getting very good results.
thingiverse
This thing consists of the parts you need to print, if you want to build my 8mm film scanner. It runs on Arduino, and utilises a genuine Bolex film gate from the 1960s. See the thing run on my blog, as well as instructions on how to build one:...
thingiverse
(Credit to siftu for the suggestion!) I think adding the connectors to the film mounting base holder will allow a 3D printed spool holder to be made so that they can sit on the sides. Also probably need to swap out the mounts for something that...
thingiverse
The device is designed for digitizing photos using the camera in macro mode for the pentax optio 6 camera, printed with petg plastic, the temperature became 55 degrees, the nozzles 245 degrees,I used an led flashlight as the illumination.
prusaprinters
Instead of screws, the parts are now held together with a piece of 1.7mm filament.You can find the project here:https://hackaday.io/project/167426-8mm-film-scannerAnd an article about it on HackSpace magazine...
thingiverse
This holds two Kodak Films Discs on the scanner bed for precise and easy scanning. ... Still a work in progress, but it has worked so far.