aqara door sensor 3d models
109006 3d models found related to aqara door sensor.thingiverse
I designed this case in Fusion 360 for an Aqara door sensor mainly to use it for projects where I use this sensor as a general purpose zigbee sensor and I prefer something a bit smaller. There are 2 versions, one with a hole and one without it,...
prusaprinters
I designed this case in Fusion 360 for an Aqara door sensor mainly to use it for projects where I use this sensor as a general purpose zigbee sensor and I prefer something a bit smaller. There are 2 versions, one with a hole and one without it, and...
prusaprinters
This is the cap for the magnet side of an Aqara Door sensor, I had one mounted on a sliding door too close and it got obliterated by the sliding door closing unfortunately so I measured up another one I had to replace it.Its not exactly the same but...
prusaprinters
This is my version of a a window handle sensor using an Aqara Door Sensor.The main frame of the model houses the Aqara sensor board, using two pegs to place it with a friction fit. ...Hopefully future Aqara boards use the same layout so the pegs fit...
thingiverse
Here is a simple hinge mechanism for installing an Aqara door sensor on your garage door. I used some small magnets to attach it to the metal frame of the garage door, which makes it easier to reuse later on. ...There is also a version without a cutout...
thingiverse
A simple holder for the Xiaomi Aqara Door and Window Sensor. ...Use the extra double sided tape included with the sensor to install.
thingiverse
A support for the Aqara door sensor (v2), to replace the wired sensor and be able to connect your rain gauge with Zigbee! ... I use this rain gauge : https://fr.aliexpress.com/item/2026877912.html Based on this DIY project :...
thingiverse
Housing for an Aqara door/window sensor that can be used to embed the sensor into a door/window frame.
thingiverse
this hides the xiaomi door sensor in the door (topside) you need a router with a 20mm bit for the correct radius to get a nice fit and a smaller routerbit for the deeper hole. you also need to glue a thin magnet you can find in your local hardware...
thingiverse
I modified mcseven's everything box to fit a xiaomi aqara doorwindow sensor. I used a piece of seal cord i had on hand. I used the magnet's adhesive tape to stick the magnet to the bottom (not lid) half of the enclosure. I did not use adhesive...
thingiverse
plates and spacers for door sensor and magnet. 5 and 10 mm spacers, stackable. ...and fusion files included, so easy to make your own custom size.
thingiverse
Housing for the Aqara window/door sensor. ... I designed this because I saw some designs that felt like there were too many parts and I just wanted 1 part per half of the sensor.
thingiverse
Holder / case for Xiaomi (V2) Aqara Door sensor and magnet. For the V1 (round) version, see https://www.thingiverse.com/thing:2791484. You can get it easy out for battery change. You can stick it to the wall or use some screws. I printed with ABS....
prusaprinters
Holder / case for Xiaomi (V2) Aqara Door sensor and magnet. For the V1 (round) version, see <a href="https://www.thingiverse.com/thing:2791484">https://www.thingiverse.com/thing:2791484</a>.</p> <p>You can get it easy out for battery change.</p>...
thingiverse
I've remixed GrRivero's Xiaomi Aqara Door Window Sensor to fit my entrance door, it increases the height by 27mm from base. Slide the magnet part in from one side. I've used supports for the upper thin part, but was unable to remove the supports...
thingiverse
Weatherproof enclosure for the Aqara Door & Window Sensor for mounting to a gate or door outdoors. The smaller part of the sensor pair is a magnet and doesn't require weatherproofing, but I wanted to have a coordinating mount for that, so they're a...
youmagine
I've remixed Aqara Door Window Sensor to fit my entrance door, it increases the height by 27mm from base. Slide the magnet part in from one side. I've used supports for the upper thin part, but was unable to remove the supports (20%) without breaking...
thingiverse
I designed this back cover for the AQARA door window sensor, cause it broke. Should fit directly, if not try to change the scale in your slicer by 1-2%. ... If u like my work, u can support me by checking out after using one of this links: AQARA doow...
thingiverse
This is a simple low profile plate that allows mounting of the Aqara window/door sensors in a removable way (e.g. if you rent, if you want to paint, etc only leaves a tiny hole to fix) but still keeping them securely attached. I recommend you use...
thingiverse
Soporte para el imán de los sensores de puertas/ventanas de xiaomi aqara. Lleva un tope para poder pegarlo y que no se caiga. ...
thingiverse
Created to house the Aqara sensors I'm using for my automatic car gate. ...I recommend using silicone sealant to provide additional waterproofing.
thingiverse
**Design constraints** - The need of just one sensor per double window - No false positives when window is unintentionally closed by fast air movement - slim design, non-disturbing during daily use **Parts list** Per double window and sensor you need...
thingiverse
Project to use a window or door sensor as a water leak sensor.
thingiverse
Aqara door and window sensor housing for outdoor.
thingiverse
A simple holder for the Xiaomi Aqara Door and Window Sensor. ... Use screws or double sided tape to install.
cults3d
A simple holder for the Xiaomi Aqara Door and Window Sensor. ... Use screws or double sided tape to install.