aqara motion sensor 3d models

A simple holder for aqara motion sensor. ...Can be used for wall and ceiling mount.

A small holder for Aqara Motion Sensors.It has a hole for M5 screws. ...You can also use doublesided-tape to mount it.

More information about the Xiaomi Aqara motion sensor can be found here: https://www.automatiserar.se/xiaomi-aqara-motion-sensor/ If you'd like to buy this mount, it's possible in Sweden through this link:...

This is a frame to mount your Xiaomi Aqara motion sensor using u Gira (donor) switch and a Gira system 55 frame. ...Remove the frame from the switch like shown in the photos.

A simple and quick to print magnetic support for Aqara motion sensor.  Requires 4 round magnets, diameter 8mm, width 2mm (real world measurements are more like 7.8mm and 1.5mm). If you want to use other magnets size, the f3d design is included,...

Here is a rewritten version of the text: This wall mount for Aqara motion sensor makes it easy to secure the device to a wall or ceiling using a small clip, eliminating the need for a two-sided adhesive strip.

I opted for a basic holder to securely fasten my Xiaomi Aqara motion sensor against the bathroom's tile work, looking for a straightforward solution that would keep it firmly in place.

This is just another wall mount for the Xiaomi Aqara motion sensor. ...I wanted a simple holder that I can stick to the tiling in the bathroom.</p> <h3> Print Settings</h3> <p><strong>Resolution:</strong></p> <p>0.2</p> <h3> <p class="detail-setting...

The case for the Aqara Motion Sensor P1 can be used to mount the sensor to a wall using screws. The holes at the top and bottom can be used to put a square screw nut into it. You are flexible to decide between both. Simply drill a hole for the screw...

Aqara Human Body Sensor Holder Stand 360 Degree Free Rotation Motion Sensor Base for Mijia Body Aqara body sensor

wall mount for motion sensor, included a 20 degree tilt adapter, in fusion360 can join to one part for easy printing, and easy to change angle if needed. sensor sit well without any help, but a little bit off double side tape will be better. Edit.

As the swivel mount needs to be glued to the sensor opening / changing is not easily done. ...Therefore I created a simple magnetic adapter.Needs 6x3 magnets that are press fitted.

The hole is actually more accurately aligned, mine is just a little off due to me cramming some paper in it.

A miniature reinterpretation of https://www.thingiverse.com/thing:3585549 has been created. A hole was carefully inserted and the rear section elevated slightly. Additionally, the rear's width was augmented to accommodate the newly added opening. ...The...

Straight angle (25 degree) support for Aqara Motion Sensor

Aqara Motion Sensor Wall Mount for Ikea Skadis pegboards Needs to be printed with supports for the rear hook

This is a custom mount for my Aqara motion sensor, integrated with a home security system to meet my specific needs. I require it to be securely positioned at eye level in the living room for optimal monitoring purposes. Since the adhesive sticker...

Angled motion sensor holder 30 degrees

I made this outdoor mount for the Aqara P1 zigbee motion sensor, this is made in 2 versions, one for application on a 40 mm column and one for wall application. Both applications protect the sensor from rain and bad weather, the only part that...

------- Mount for an Aqara P1 motion sensor with 22.5 degree inclination. The P1 sensor can simply be plugged in and then sits so tight that even an overhead mounting is possible (without guarantee!). Even without screws, the mount incl. P1 stands...

I got tired of having my aqara motion sensors for my smart home sitting out on counters and getting knocked out of position or just plain looking ugly. So I decided to incorporate it into a tissue box holder to help make it blend in...

Mount with a screw inside the corner tip.

I had the desire to beef the optics of the Aqara Motion Sensor a bit up so I designed a little tripod. There is no improvement for the sensor itself, it just looks better :) Print it facing the 3 legs to the top. You will need to enable supports. ...I...

I Made It Even More Beautiful

Corner and flat mounts for Aqara sensors - The corners are overly large as to cover / match the anchors of existing sensor mounts I had. Print instructionsPrints without supports. ...Each type requires a sensor 'cup' to be printed with it, and the cup...

Support for xiaomi mi motion sensor AQARA, Glue the bolt with double sided tape and screw the support on it. Orientation in all directions. Support pour détecteur de mouvement Xiaomi AQARA . Poser le boulon au double face et visser le support...

Plug instead of motion sensor siemens/legrand for Mi Smart Home Motion Sensor / Xiaomi Aqara Body Sensor

Here is a small holder for the Xiaomi Aqara Motion Sensor motion sensor (RTCGQ11LM). Assemble the holder with an M3 screw. You can use either a screw or a 10x2 magnet. If you are satisfied with my work, please consider supporting me on future...