aqara motion sensor 3d models

Materials: - Xiaomi Aqara Zigbee Button (https://bit.ly/3BeIQVi) - 3M Command Strip - Small Sized...

I made a basic enclosure for the Xiaomi Aqara WXKG11LM smart button to use it as a doorbell. It turned out larger than I had envisioned, but I needed to ensure that rain wouldn't seep in. The enclosure is printed in two parts: - A base plate that...

simple Converting the Circular motion into Reciprocating motion mechanism

simple Converting the Circular motion into Reciprocating motion mechanism

This is designed to fit the Wyze Motion Sensor V2. ...Included is both a flat mount and a corner mount.

This is a case for combining a PIR motion sensor and an AM2302 temperature/humidity sensor together with a WEMOS D1 Mini module to make an environment sensor for use in home automation. For reference, the specific components I used are: AM2302...

Sensor - Sensör Solidworks ile Sensör Tasarımı Sensor Design with Solidworks

Colors: 4 Н 75 х Ø 360 mm

Customized version of https://www.thingiverse.com/thing:266912 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=266912

Инфракрасный датчик движения (ИК-датчик отделен от основного блока), совмещенный с датчиком освещенности.Корпус + сенсор. Габариты с натуры. ...Длина провода тройного ~164 мм, четырёхжильный на сенсор - 220 мм.SW2021

This reusable lid fits perfectly on our 250ml refill bottles of hand wash, allowing you to ditch those expensive brand-specific refills and fill up with your preferred hand soap instead.

I was asked to create a mount for wall edges. Here we are. ... There are two versions; 90 Degree Orientation (this model) 45 Degree Orientation (see my designs) Recommendation to use screws as in the picture (3,5mmx30mm)

I was asked to create a mount for wall edges. Here we are. ... There are two versions; 90 Degree Orientation (see my designs) 45 Degree Orientation (this model) Recommendation to use screws as in the picture (3.5mmx30mm)

... wall mount for Eve Motion sensor. ...It can be use for any other sensors or small cameras.You need 2x M4 screws and 1x M3 screw.The M3 screw need as a hook for the Eve Motion sensor. Printing nfo:Resolution: 0.2Support: Yes for part 1Infill: 30-40%

I made this simple wall mount for Eve Motion sensor. It can be use for any other sensors or small cameras. You need 2x M4 screws and 1x M3 screw. ... The M3 screw need as a hook for the Eve Motion sensor.

This design is a straightforward Raspberry Pi holder that securely cradles a RadioShack brand motion sensor. ... Layer Height: 0.2 millimeter Supports: None

Stand for Xiaomi motion sensor with 360° rotation, for easy battery replacement because it is only plugged in. ... M4x10mm screw needed to connect adapter to bridge

This is a case for combining a PIR motion sensor and an AM2302 temperature/humidity sensor together with a WEMOS D1 Mini module to make an environment sensor for use in home automation. For reference, the specific components I used are:...

Motion sensing night light to light of bathroom Arduino code: //basic night light // A0 pin for LDR // A1 pin for motion sensor // LED1 led output on pin 9 // LED2 led output on pin 10 int LED1 = 9; int LED2 = 10; void setup () { // set up I/O...

... ...This project has far-reaching potential, making it an ideal solution for various surveillance needs. To explore the project's full capabilities, check out the instructable link below: https://www.instructables.com/id/DIY-Motion-Sensor-ESP-8266/

More information about the motion detection in my YouTube video: https://youtu.be/z6LABh3M6yE For this project, I used: - Wemos D1 mini - PIR sensor - light resistor - Fun :) Link to the ino file for the Wemos D1:...

2021/6/6 I designed a simple and new reciprocation linear accessory that converts rotational motion to linear motion. It can save a lot of space. Using the fusion 360 project function it is easy to project a complex curve to surface. ... ...

2021/6/6 I designed a simple and new reciprocation linear accessory that converts rotational motion to linear motion. It can save a lot of space. Using the fusion 360 project function it is easy to project a complex curve to surface. ... ...

2021/6/6 I designed a simple and new reciprocation linear accessory that converts rotational motion to linear motion. It can save a lot of space. Using the fusion 360 project function it is easy to project a complex curve to surface.

2021/6/6I designed a simple and new reciprocation linear accessory that converts rotational motion to linear motion. It can save a lot of space. ...Using the fusion 360 project function it is easy to project a complex curve to surface.

2021/6/6I designed a simple and new reciprocation linear accessory that converts rotational motion to linear motion. It can save a lot of space. ...Using the fusion 360 project function it is easy to project a complex curve to surface.

Users develop a basic shield or enclosure to safeguard their Leap Motion Sensor from dust and moisture, along with protection for the USB cable connection, to ensure a stable link during demos in various settings. ... Designed specifically for mounting...

These are hoods for motion sensors to constrain what the sensor sees. Primary intended usage is for feet sensing on staircases, i'm sure there are plenty of other applications. ... These work with Sonoff and unbranded aliexpress sensors attaching just...

Motion analysis

A rotary wheel is designed to attach to its base, transforming rotational movement into linear and angular motion. ...This easy-to-assemble device can be 3D printed, making it an ideal teaching aid for physics students seeking practical demonstrations...