aquaclear 50 3d models
127450 3d models found related to aquaclear 50.thingiverse
An Intake adapter for the Fluval Aquaclear 50 Powerhead. This allows you to install a Fluval Pre-Filter sponge preventing small fish and invertebrates from being sucked into the powerhead, this also has the added benefit of adding additional...
prusaprinters
An Intake adapter for the Fluval Aquaclear 50 Powerhead. This allows you to install a Fluval Pre-Filter sponge preventing small fish and invertebrates from being sucked into the powerhead, this also has the added benefit of adding additional...
thingiverse
Years ago I made a media basket for my Aquaclear 50 filter based of some designs I saw online with acrylic glass a couple drill bits and silicone. A few years have passed and the silicone is starting to fall apart so I decided to design and 3d print...
thingiverse
Remix of droodles flow diverter. ... This one fits the Aquarclear 50 model.
thingiverse
I like to over filter my tanks so I use a Aquaclear 50 on my 20 gallon tall. At its full output, the current is too strong for the tank so I designed a current deflector that snaps right onto the filter and lowers the kinetic energy of the water as...
cults3d
PLA should be aquarium safe. I have a round feeding circle in the tank for 2 years now, no problem. I was able to print mine with 0 infil, and 2 layers walls with a 0.8mm nozzle. ...if you use a .4mm nozzle try 3 layer walls
thingiverse
PLA should be aquarium safe. I have a round feeding circle in the tank for 2 years now, no problem. I was able to print mine with 0 infil, and 2 layers walls with a 0.8mm nozzle. ... if you use a .4mm nozzle try 3 layer walls
thingiverse
I designed this to connect an AquaClear 50 to a large Marineland pre-filter sponge, eliminating dwarf shrimp in my filter. ...Without this fitting, this sponge is too large for the tubing on the AquaClear.
prusaprinters
Tested with my FLUVAL AquaClear 50, but should work on most other AquaClear hang-on-back filters as I believe they all have the same intake tube diameter.PrintingI printed it with a 0.1mm layer height (but used adaptive layers to cut down on print...
thingiverse
Created a surface skimmer for the Aquaclear 70 You will have to adjust the height of the surface skimmer to make sure it doesnt get bubbles. ...Either move the height of the surface skimmer of adjust the intake speed of the Aquaclear 70
thingiverse
Just one of those little supports that everyone seems to lose off the bottom of AquaClear filters. ... It's a bit thicker than the original for extra durability and it's not an exact replica, just something I whipped up quickly.
thingiverse
I have it attached to my Aquaclear 20 and it handles the water flow on full, with new cartridges. It snaps/pushes on and requires no other support. Snap/push it on GENTLY as the plastic can crack underneath if your printer doesn't nail the...
thingiverse
Remixed from "Surface skimmer for Aquaclear 20 HOB filter" Resized the cylinder to accurately slip fit onto my AC30 intake tube. Fixed the floor of the box to print the right number of layers at Cura's default 0.2 mm profile. At this time it still...
thingiverse
This is in a nano aquarium that gets a 50% water change once a week. Plastics leech things off very slowly, so there shouldn't be hardly any chemicals finding their way into the water. I purposefully didn't add grating to the front of the basket...
thingiverse
... surface area for air exchange. The result is a significantly less turbulent tank with the majority of the water flow going straight down the back wall, to the bottom, and then out to the sides. Supported HoB filters: Aquaclear 20 Aquaclear 30
cults3d
A sock-spacer for the AquaClear 20 to make it baby shrimp safe .The sock i use was used to be sucked in the inflow slits so i had to clear it every 3-4 days because the water flow was near zero.
thingiverse
A sock-spacer for the AquaClear 20 to make it baby shrimp safe .The sock i use was used to be sucked in the inflow slits so i had to clear it every 3-4 days because the water flow was near zero. ...
thingiverse
A small surface skimmer for a hang on back Aquaclear 20. I removed the bottom piece of the nozzle. The surface skimmer box then slides right up to the AC nozzle. The right side where the outlet sits, is has no teeth, so it does not skim the water...
thingiverse
This is a refillable carbon box for aquaclear/topfin 20 filters, although it can be resized to fit all sizes. Simple add activated carbon to the box, rinse the box under cold water (to wash away dust) and place in aquarium filter between the sponge...
thingiverse
#### Surface Skimmer box for AquaClear 20 aquarium filter. - Designed for rimless aquarium with 6 mm glass thickness or less. #### Advantages - Keeps water surface clean and free of oil film. - Small profile creates minimal distraction in...
thingiverse
This replacement lid fits snugly on an Aquaclear 70 hang on back filter 21.2cm x 15.2cm x 1.3cm. The design is quite robust and could comfortably have 1-2 mm sliced off the bottom (as oriented) to save on filament without hurting strength much. ...
prusaprinters
This replacement lid fits snugly on an Aquaclear 70 hang on back filter 21.2cm x 15.2cm x 1.3cm. The design is quite robust and could comfortably have 1-2 mm sliced off the bottom (as oriented) to save on filament without hurting strength much. On...
grabcad
.50 cal (Scope is included in the download, you just need to make it visual again in the assembly)(Not original work)
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=16610 Instructions Using the following options: cornerradius = 4 spines = 10 thickness = 2 spineoffset = 10 screwinset = 4 borderthickness = 5 size = 50 screwradius = 2.3 spinesize = 2...
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=900277 Instructions Using the following options: thickness = 6 helix_angle = 0 clearance_percentage = 5 hole = 5.2 num_teeth_or_pitch = 50 gear_type = 1 height_of_rack = 10 hole_type = 1
grabcad
http://www.mfcad.com/tuzhi/839/415980.htmlIt is there to be downloaded for 50 Mu Wind Coins. Great to see my model is worth so much. ...You are not only stealing, but also confirming a prejudice about the Chinese....Shame on you!!!I had to prove this...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: font_size = 32 font_outline_width = 1 bar_width = 48.5 textextruder = extruder2 outline_color = Gray lug_width = 0 lug_style = plate...