aquarium frag rack 3d models
33558 3d models found related to aquarium frag rack.cults3d
reef aquarium frag rack coral holder dimensions 77.5 x 150 mm for 10mm thick glass
thingiverse
Frag rack sections for saltwater tanks. Fusion 360 .F3D file is also attached. You use at least 2 Connecting Pieces to connect 2 sections of Egg Crate together. Connecting Pieces are probably going to be friction-fit depending on the Settings...
thingiverse
My frag plugs are too long even with the holders from the original models. ... I added some 1 inch legs to the frag rack and now it is perfect. ... I also extended the connector to the new rack height
thingiverse
3 Coral frags Racks for reef Aquariums for 4 and 5 plots. ...Fixed or customizable height
cults3d
3 Coral frags Racks for reef Aquariums for 4 and 5 plots. ...Fixed or customizable height
cults3d
I Designed this Frag Rack to be as modular as possible Build your own interlocking rack system for growing or displaying coral! No supports required This set contains the following models Basic rack (Regular basic rack intended as a single functional...
thingiverse
A support column for holding up aquarium frag racks. I have had to print it solid at 100% infill to get it to sink. ...I'm using PET+.
myminifactory
Frag Plugs used in picture :Top: 20mmStem: 10mm Suction Cups:Uniclife 12 Pcs Aquarium Heater Suction Cups Suckers Clips 33mm Dia Holders/Clamps for Fish Tank Black(non-affiliate...
thingiverse
Frag Plugs used in picture : Top: 20mm Stem: 10mm Suction Cups: Uniclife 12 Pcs Aquarium Heater Suction Cups Suckers Clips 33mm Dia Holders/Clamps for Fish Tank Black (non-affiliate link):...
thingiverse
A basic frag rack for coral frags in a reef aquarium. 4x 12mm holes for the frag plugs. 2x 6mm holes for the suction cups. ... Some cheap 20mm suction cups from ebay were a perfect fit.
cults3d
This small magnetic frag rack should be printed in petg for any aquarium use. ... Fits round coated magnets up to 30mm diameter
thingiverse
Simple frag rack that holds 7 frag plugs. ... 50mm tall, prints very quickly, ideal for using to acclimatise coral frags while on your sand bed.
thingiverse
This is a magnetically mounted frag plug rack for marine aquariums. It was printed in PLA, but I suggest ABS or PETG for the longest life. Uses 32mm x 2mm rare earth magnets, available from numerous online sources. Mine came from Amazon. The...
thingiverse
This is a magnetically mounted frag plug rack for marine aquariums. It was printed in PLA, but I suggest ABS or PETG for the longest life. Uses 32mm x 2mm rare earth magnets, available from numerous online sources. Mine came from Amazon. The...
thingiverse
Square rack for coral frags. ...Made to easily four of them in a 17" cube tank.
thingiverse
This is a mini Frag Rack, optimized for a Red Sea Reefer. It holds up to 5 small coral frags. ...Optimal for zoanthus and small corals
thingiverse
The rack is held by two magnets. ... Use old magnets. works also with frag plugs use PETG no PLA
thingiverse
Small Frag Rack - printed with PETG, holds 6 frags and fittable dollarama ceramic magnets on each side of wall. ... ceramic magnet: https://www.dollarama.com/en-CA/p-clear-coloured-magnets-assorted-sizes-and-colours/3011612
thingiverse
Simple frag rack designed to use home depot magnets. The plugs should be printed solid (100% infill). I used the xenia plugs with a small shell on top. ...
thingiverse
These legs snap in at the holes of a eggcrate plate to lift the racks in your frag tank from the ground.
thingiverse
This is a frag rack that I designed to hold up to 10 3/4" frag plugs. I printed in PETG. It is designed to work with the suction cups shown in the photo. ... They are available from HomeDepot for around 2$ a pack.
cults3d
Frag rack capacity : 20 plugs you have to buy 4 suction cups 3 cm in diameter (amazon or others...) remove the thin layer of seaweed and fix the suction cups. ... 27*7*5 cm
thingiverse
Feet are 1/2" in Diameter by 1-1/4" tall, and hold the frag rack (Egg Crate) 1 inch above the bottom of your bare-bottom reef tank or frag tank. Print with 100% fill so the feet aren't too buoyant. Since it is tall with a small base, print...
thingiverse
A small 3D printable frag rack. All that is neede extra are some magnets. 4 x small N52 Neodynium magnets to be exact or whatever else you have lying around which is appropriate. ... Below is a link where I bought mine: ...