ar 10 vise block 3d models

... on their opposite side. I have not tested this design but should be significantly stronger with the bolts in place. This was created by the recommendation of ValleyWalker, and referenced Timpanzi's AR-15 version, (Thingiverse file: 4145773).

This is a variation on my other AR-10 Upper Receiver Vise Block. I had received some feed back that some users snapped theirs during assembly, and there was recomendations that I add the ability to add bolts. So I did. This design is designed to...

ar vise block made to fit monoprice mini

Ar15 Vise block for working on your rifle.

Fits 9mm Glock magazine wells, so it will work for all Glocks (except the small single stack ones), all AR-9 / AR-15 in 9mm. If printed with an infill of >90%, it is as sturdy as it can be. Feel free to print for yourself, friends etc. - but...

This is a full size model of the AR-15 Upper Receiver Vise Block The vise block has vertical holes in it. It was designed to put in 3/8 x 3 inch bolts into the holes. It is one piece. there are recessed/threaded holes running horizontally so you...

__________________________________________________________________________ Designed to hold an AR-15 upper receiver in a vise. It wont work if your hand guards come back over the upper too far, or if the lower is installed. I put on the original in...

I cut off one side of the ar15 vise block by PrintedFirearm so that it would fit on a 4x4x4 printer bed. ...This is only to hold the lower receiver in the upright position and will not work to hold it upside down.

A vise block for a S&W M&P 10. ...I don't know if it will fit other AR 10

I could find ar-15 bench blocks and wall mounts but nothing for a ar-10 This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/2wZcI0g4wYq

Original file was in inches and mag catch was off. New file is in mm and should have correct mag catch location. ...

... Glock Mags. ... This is a tight fit on my gun, which is based on a Quarter Circle 10 Reciever! Might not work with other recievers... Update: 30/03/2020 added V2 of the PCC Block, with this version now the gun is horizontal when clamped in a vise.

This is an Aero Precision (DPMS) style upper receiver vice block that I designed and used to assemble the .308 Ar-10 upper receiver. This final version was used to torque the barrel down and handled up to 75 ft/pounds of torque without any issues. ...It...

This is an Aero Precision (DPMS) style upper receiver vice block that I designed and used to assemble the .308 Ar-10 upper receiver. This final version was used to torque the barrel down and handled up to 75 ft/pounds of torque without any issues. ...It...

modeled in Maya, painted in Substance Painter. ...The AR-10 is a modified version of the popular AR-15. Instead of firing the .223/5.56 cartridge, it fires a .308 and is optimized for long range shooting. ...Most widely used for hunting big game.

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/2wZcI0g4wYq

reverb vise block 10mm hole diameter

STI 2011 magazine well vise block. ...Holds STI 2011 pistol in vise.

Vise Block for Guntec DPMS 308 Low Profile Upper Receiver.

AR-15 Vise Block originally downloaded from Fosscad. ... For more info check out my blog http://www.printedfirearm.com Originally printed on a...

TL;DR Strong AR upper receiver vise block. ... Use 3/8" x 3" bolts in the vertical holes (bolt head at bottom) Use 1/4" x 1" (20 TPI) in horizontal holes Probably will need to clean up 1/4 x 20TPI holes with a tap, or screw before threading all the...

This is a V-Block I made to use on a vertical mill vise for machining etc.

Made this cutout so that it would fit around the square screw of my small vise and allow the entire bottom section to be clamped securely. ... Printed with 75% infill PLA +

modified ar15 vice block with a wide base

... warpage. This fits diagonally in a Ender print bed. This is strong enough for basic assembly of the rifle but will twist if you try to use it to torque the barrel nut. Do not use when tightening the barrel to final torque, the vise will break.

I made this ar10 vise mount but wanted a stand for it as well. I made this about .5mm loose on both sides to account for printing variations but works freat with my mount. ...I printed it a 50% infill .3mm height and 100spd.

AR-308 GAS BLOCK

One step of assembling an AR-15 is to clamp the gas tube into the gas block by pressing in a roll pin. That takes a lot of force. This print holds the gas block securely so you can press/hammer the roll pin. Designed to fit a gas block from Aero...

A simple AR-15 vice block built in Blender

AR Armorers block   Inserts into  AR 5.56 magwell and retains with mag release.