ar 15 jig 3d models
177186 3d models found related to ar 15 jig.thingiverse
This is version 3.2 of my AR-15 lower jig. Parts lists and instructions are included in the documentation. Long-form video instructions and backups of the filepacks can be found on my Odysee channel: https://odysee.com/@swolebro:4 I've also...
prusaprinters
This is a jig to help with the assembly and disassembly of an AR-15 Bolt. I was unhappy with the designs I saw available so I designed my own.The bolt locks into place via lugs built into the base of the jig, and the tail is captured, but...
cults3d
4 Socket cap, Stainless steel 18-8, 1/4"-20 x 2-1/2" 4 Hex nuts, Stainless steel 18-8, 1/4"-20 4 Metric socket cap, Stainless steel 18-8 (A-2), 5mm x 0.8mm x 20mm 4 Metric hex nuts, Stainless steel 18-8 (A-2), 5mm x 0.8mm
thingiverse
A jig to hold the AR 15 bolt while you work on the ejector / extractor. PLA+ 225C 60C, supports yes 55 degrees, infill 100%, walls 4, .15 res Parts needed. ... 1 spent 5.56/2.23 casing (cut off about 10 mm from the primer side and attach this to the end...
thingiverse
A jig to hold the AR 15 bolt while you work on the ejector / extractor. PLA+ 225C 60C, supports yes 55 degrees, infill 100%, walls 4, .15 res Parts needed. ... 1 spent 5.56/2.23 casing (cut off about 10 mm from the primer side and attach this to the end...
grabcad
This is a 3D printable AR-15 drill bit jig and it is a direct copy from the juggernaut tactical jig. ...I accidentally damaged my jig after the first round of drilling, and the price of getting a new one inspired me to reverse engineer it.
thingiverse
A printable ar15 test jig, the structure should be strong enough to hold the spring force, havn't test it out because I'm not an American. So, you American folks are welcomed to give it a try . Posting some photos would be even better.Notice i also...
thingiverse
This is a jig to help align punches to remove the front sight / gas block on SMITH AND WESSON AR15 with the standard A2 sight and bayonet leg. Because S&W pins are reversed from the industry standard this will only work on S&Ws. I've included the...
grabcad
Just drew them up on solidworks via a drawing that I found online. ... I was able to mate them perfectly to a model of the lower that I know to be correct and it lines up perfectly...Enjoy!
grabcad
AR-15_80_percent_Lower_Drill_Jig_v1-ShadowfallThis is found In FOSSCAD - Re-hosting - **Added Trigger Slot Location
thingiverse
For instructions on how to use this jig, please visit the following link: https://www.80percentarms.com/content/Jig_Manual_80_Percent_Arms.rev1.1S.doc.pdf The drilling plate adapter isn't required so it has been omitted. ...For this reason, begin after...
thingiverse
Intended to assist with the install of mil spec AR15 trigger. Holds the disconnector and disconnector spring in place while more easily putting pressure on the trigger spring (rather than putting pressure with your finger on the thin disconnector.
thingiverse
1 milling jig assembly posted by @digitaldash (thing:4908033). I have not yet had the chance to test this out myself. That being said, if you choose to use this to finish out an incomplete lower receiver of your own it is, of course, at your own...
grabcad
AR-15 assembly. Missing a few small parts like springs, but otherwise OK. All parts are mated appropriately. Modelled with SolidWorks 2012. ...And all parts are built with native features, not simply imported surfaces.
thingiverse
This is a jig for holding your ar-15 charge handle for laser engraving