ar 15 upper receiver vise block 3d models
282019 3d models found related to ar 15 upper receiver vise block.thingiverse
__________________________________________________________________________ Designed to hold an AR-15 upper receiver in a vise. It wont work if your hand guards come back over the upper too far, or if the lower is installed. I put on the original in...
thingiverse
This is a full size model of the AR-15 Upper Receiver Vise Block The vise block has vertical holes in it. It was designed to put in 3/8 x 3 inch bolts into the holes. It is one piece. there are recessed/threaded holes running horizontally so you...
thingiverse
... on their opposite side. I have not tested this design but should be significantly stronger with the bolts in place. This was created by the recommendation of ValleyWalker, and referenced Timpanzi's AR-15 version, (Thingiverse file: 4145773).
thingiverse
... thickness is reduced as well to accomodate the opening distance on the 3-in vice from harbor freight. The total length of the fingers has been reduced to ensure that the upper receiver is being clamped, not the fingers against the opposing block.
thingiverse
TL;DR Strong AR upper receiver vise block. ... Use 3/8" x 3" bolts in the vertical holes (bolt head at bottom) Use 1/4" x 1" (20 TPI) in horizontal holes Probably will need to clean up 1/4 x 20TPI holes with a tap, or screw before threading all the...
cults3d
This is a variation on my other AR-10 Upper Receiver Vise Block. I had received some feed back that some users snapped theirs during assembly, and there was recomendations that I add the ability to add bolts. So I did. This design is designed to...
pinshape
1:1 scale Upper Receiver (with Dust cover and Forward Assist Button) for Ar15 Compatible with most lower receiver
thingiverse
This is the required vise block to assemble the Light Practical Carbine upper receiver.
thingiverse
Upper receiver cover for the AR15 platform, remixed from ZBROYAR's cover (https://www.thingiverse.com/thing:2816693). This allows you to store your upper and Bolt Carrier Group together, and prevents dust/dirt/whatever intrusion into your receiver. ...
thingiverse
I cut off one side of the ar15 vise block by PrintedFirearm so that it would fit on a 4x4x4 printer bed. ...This is only to hold the lower receiver in the upright position and will not work to hold it upside down.
thingiverse
... (stressed areas will be 100% solid, rest is "30% infill by design") 2. 100% solid to play with infill or for non FDM printers Pins can be attached to cover body using dedicated holes. Enjoy clean range bag and no extra stuff in your upper :)
grabcad
this is a simple upper receiver design i came up with, it is made from an inner 1.25" tube steel inside and an outer sheet metal component welded or riveted together to make up an AR-15 upper receiver, this would result in less wear and friction...
thingiverse
This is an Aero Precision (DPMS) style upper receiver vice block that I designed and used to assemble the .308 Ar-10 upper receiver. This final version was used to torque the barrel down and handled up to 75 ft/pounds of torque without any issues. ...It...
cults3d
This is an Aero Precision (DPMS) style upper receiver vice block that I designed and used to assemble the .308 Ar-10 upper receiver. This final version was used to torque the barrel down and handled up to 75 ft/pounds of torque without any issues. ...It...
thingiverse
This is designed to hold your AR15 upper receiver in a vise so you can work on it or assemble it. I recommend printing this at a high infill to support the weight of the upper and resist crushing by the vice. Also you will need to use a raft to...
thingiverse
This is an AR15 upper vice block for assembly. Do not print it vertical as the layer adhesion will fail. I have not attempted to print it on its side but if you print it sideways it may hold up. After assembly, ream out the pin holes with a...
cults3d
This is an AR15 upper vice block for assembly. Do not print it vertical as the layer adhesion will fail. I have not attempted to print it on its side but if you print it sideways it may hold up. After assembly, ream out the pin holes with a 1/4...
thingiverse
Original file was in inches and mag catch was off. New file is in mm and should have correct mag catch location. ...
thingiverse
This is a remix of the LEFT vise block for a dedicated 9mm upper. This works with the Aero EPC-9 - Enhanced Upper Receiver. ...I have not tested it with other dedicated 9mm uppers.
cgtrader
My first design of AR-15 Quick detach barrel system. ...The concept similar like Cry Havoc tactical, Dolos and Leo Takedown QD barrel system
thingiverse
Vise block for .308 lower receivers based on the DPMS LR308 standard. ... www.applied-kinetics.com 6/24: corrected spelling (I r enginear) reoriented object for printing (rotated for correct orientation) Instructions beware of warping it is a large...
grabcad
I have not verified any of the dimensions with an AR-15 spec drawing, therefore, I would not use this model to craft any part for an AR-15. This model should be used as a graphical representation only! ...I do not have the bolt included as I am in the...
cults3d
I have deliberately moved the Trigger, Hammer & Safety holes so as to keep this a non functioning weapon the Magazine and take-down pins are the only things that work on this lower, it is only intended for cosplay and to show how an AR functions. ...I...
thingiverse
Fits 9mm Glock magazine wells, so it will work for all Glocks (except the small single stack ones), all AR-9 / AR-15 in 9mm. If printed with an infill of >90%, it is as sturdy as it can be. Feel free to print for yourself, friends etc. - but...
thingiverse
Used for cleaning our AR, keeps the rear open while on a support.
cults3d
Used for cleaning our AR, keeps the rear open while on a support.
thingiverse
Based on my previous thing, this allows you to mount your AR-15 into a vice to let you work on it. With a high enough infill and proper print orientation PLA should be strong enough for your needs, but if you're going to be cranking super hard on...