ar vise block upper 3d models
111918 3d models found related to ar vise block upper.thingiverse
This is a full size model of the AR-15 Upper Receiver Vise Block The vise block has vertical holes in it. It was designed to put in 3/8 x 3 inch bolts into the holes. It is one piece. there are recessed/threaded holes running horizontally so you...
thingiverse
__________________________________________________________________________ Designed to hold an AR-15 upper receiver in a vise. It wont work if your hand guards come back over the upper too far, or if the lower is installed. I put on the original in...
thingiverse
... on their opposite side. I have not tested this design but should be significantly stronger with the bolts in place. This was created by the recommendation of ValleyWalker, and referenced Timpanzi's AR-15 version, (Thingiverse file: 4145773).
cults3d
This is a variation on my other AR-10 Upper Receiver Vise Block. I had received some feed back that some users snapped theirs during assembly, and there was recomendations that I add the ability to add bolts. So I did. This design is designed to...
thingiverse
TL;DR Strong AR upper receiver vise block. ... Use 3/8" x 3" bolts in the vertical holes (bolt head at bottom) Use 1/4" x 1" (20 TPI) in horizontal holes Probably will need to clean up 1/4 x 20TPI holes with a tap, or screw before threading all the...
thingiverse
This is designed to hold your AR15 upper receiver in a vise so you can work on it or assemble it. I recommend printing this at a high infill to support the weight of the upper and resist crushing by the vice. Also you will need to use a raft to...
thingiverse
This is an AR15 upper vice block for assembly. Do not print it vertical as the layer adhesion will fail. I have not attempted to print it on its side but if you print it sideways it may hold up. After assembly, ream out the pin holes with a...
cults3d
This is an AR15 upper vice block for assembly. Do not print it vertical as the layer adhesion will fail. I have not attempted to print it on its side but if you print it sideways it may hold up. After assembly, ream out the pin holes with a 1/4...
thingiverse
This is a remix of the LEFT vise block for a dedicated 9mm upper. This works with the Aero EPC-9 - Enhanced Upper Receiver. ...I have not tested it with other dedicated 9mm uppers.
thingiverse
Fits 9mm Glock magazine wells, so it will work for all Glocks (except the small single stack ones), all AR-9 / AR-15 in 9mm. If printed with an infill of >90%, it is as sturdy as it can be. Feel free to print for yourself, friends etc. - but...
thingiverse
This is the required vise block to assemble the Light Practical Carbine upper receiver.
thingiverse
I cut off one side of the ar15 vise block by PrintedFirearm so that it would fit on a 4x4x4 printer bed. ...This is only to hold the lower receiver in the upright position and will not work to hold it upside down.
thingiverse
... thickness is reduced as well to accomodate the opening distance on the 3-in vice from harbor freight. The total length of the fingers has been reduced to ensure that the upper receiver is being clamped, not the fingers against the opposing block.
thingiverse
used fusion to also load in an upper and found the specs for the gas tube hole in the upper so cut the hole in the block to fit the gas tube. thought about this a little more and am wondering if you will be able to get the vise block out with the...
cults3d
This is an Aero Precision (DPMS) style upper receiver vice block that I designed and used to assemble the .308 Ar-10 upper receiver. This final version was used to torque the barrel down and handled up to 75 ft/pounds of torque without any issues. ...It...
thingiverse
This is an Aero Precision (DPMS) style upper receiver vice block that I designed and used to assemble the .308 Ar-10 upper receiver. This final version was used to torque the barrel down and handled up to 75 ft/pounds of torque without any issues. ...It...
thingiverse
Original file was in inches and mag catch was off. New file is in mm and should have correct mag catch location. ...
pinshape
1:1 scale Upper Receiver (with Dust cover and Forward Assist Button) for Ar15 Compatible with most lower receiver
thingiverse
AR-15 Vise Block originally downloaded from Fosscad. ... For more info check out my blog http://www.printedfirearm.com Originally printed on a...
grabcad
I have not verified any of the dimensions with an AR-15 spec drawing, therefore, I would not use this model to craft any part for an AR-15. This model should be used as a graphical representation only! ...I do not have the bolt included as I am in the...
grabcad
This is a V-Block I made to use on a vertical mill vise for machining etc.
thingiverse
Upper bearing block and servo mount for Oxy 2 helicopter. ...PLA seems to work fine, just use good heat for layer adhesion.
thingiverse
This remix puts reliefs to hold nuts on the face of the upper block, allowing the block to be tightened from the back. The ability to see how much the screw extends from the nut also helps with even tightening. Print this the same was the...