ar10 barrel wrench 3d models
37440 3d models found related to ar10 barrel wrench.thingiverse
This is a wrench for opening/closing 55 gallon drum caps. ... There is a 3/8 square in the top for a ratchet if desired.
grabcad
Wrench fits a standard plastic barrel bung and a 3/8" ratchet. ... Allows for easy removal of barrel bungs without a large specialized wrench.
thingiverse
Standard 2-inch barrel bung wrench, for use on 1/2-inch driver.
thingiverse
Cap wrench for 55 gallon plastic barrels. Simple, sturdy design. ...Prints without supports laying on it's back.
thingiverse
Barrel bushing wrench for 1911 model handguns. This model is based on measurements made from the standard wrench that comes with Kimber 1911s. ... It has not yet been printed or tested to ensure that it works.
thingiverse
This is a hand wrench for the recessed cap on the common 15 or 30 gallon barrels used in many industries. I use them to haul water to a remote property and the long handled wrench people normally use is too long and cumbersome to use on a regular...
thingiverse
AR15 Platform barrel nut wrench. ... I used coarse threaded screws with a 3mm diameter Its not that great of a design, it dug into my palm a good amount, but you are free to edit and reuse this however you like
thingiverse
wolf's wrench (for the bottom part) and someone else made a nice handle I rescaled and merged the files in tinkercad to make this nice simple barrel driver. I CAN NOT FIND the original handle I used on thingiverse. my download is just the stl so...
thingiverse
... to use a longer handguard on my ASG scorpion EVO S1 with a shorter barrel to integrate a tracer unit. ...Access to the barrel nut is very limited in this configuration so I needed something to extend my reach with a 1/4 inch socket adapter. ...
grabcad
This is a tool for removing bungs from the blue plastic barrels. ... I am working on a 2 piece model (1 for head, 1 for handle) that will be much easier to cnc.
thingiverse
Customized version of http://www.thingiverse.com/thing:279864 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=279864 Instructions Using the following options:...
thingiverse
AR10- Wallmount, v.2 is just slightly smaller for better fit. Can be wall mount or bench mount, easy to screw in place and use. Keep in mind if your wall mounting stronger materials are advised. If you using on a work bench PLA is great because...
thingiverse
... I recommend to print my lighter barrel wrench instead. This one is very heavy-duty , and uses almost double the filament. At 60% infill this takes about 13-15 meters of filament to make. ... Print tested , tested on barrels and it works good.
thingiverse
I use this to install AR-10 barrel nuts with a torque wrench. AR-10 logo goes towards bolt carrier group when tightening nut. This make your torque go into the barrel and this gets the plastic to grip into the nut. ...If you do it the other way it...
thingiverse
Use this wrench to open barrels . This is the lighter version and uses alot less filament then the heavy duty version. This has been tested, and it works perfectly. ...Very tough and I was unable to break it from normal use.
grabcad
An improved barrel nut wrench for AeroPrecisions COP upper
cults3d
Functioning AR10 Receiver. The dimensions of the receiver itself are accurate. ... Please enjoy it.
cults3d
Functioning AR10 Receiver. The dimensions of the receiver itself are accurate. Please enjoy it. ... STL FORMAT.
thingiverse
A bung wrench to help remove caps common on 55 gallon plastic barrels or drums. ... Print Settings Printer Brand: Printrbot Printer: ...
thingiverse
While upgrading the tank fittings (aka bulk head fittings) on my rain barrels, I found the larger one required a giant wrench. While I could use an extra large pipe wrench, those tend to mar and/or deform the plastic (polyethylene) fittings. The...
thingiverse
This wrench will help you to screw the thread protecting nut without damaging its finish. Warning - use on cold barrel only! It is better to print this with nylon or something strong. But it will work with PLA on certain level..... ... use file...
thingiverse
.Scaled and modified to fit ar10/lr308 lowers and lock into place unlike others i could find. Added a test file with just locking part. Print at low infill for a quick way to test fitment. ...
thingiverse
Magazine stand for AR10 style magazines (7.62mm) which I use for my G&G GR25 magazines. Similar to my AR15 magazine stand (https://www.thingiverse.com/thing:757425). ... Designed in Tinkercad, prints nicely on my UM2.
thingiverse
I made this ar10 vise mount but wanted a stand for it as well. I made this about .5mm loose on both sides to account for printing variations but works freat with my mount. ...I printed it a 50% infill .3mm height and 100spd.