ar15 m4 3d models

AR15/M4 Receiver for aegs/gelblasters

Functioning AR15/M4/M16 Receiver. ...The dimensions of the receiver itself are accurate.

Functioning AR15/M4/M16 Receiver. The dimensions of the receiver itself are accurate. ... STL FORMAT.

Install the arm on the retention bolt and assemble with the M3x10 screw Use a very stiff and hard material, I had good result with PETG carbon fiber and PC/ABS Magazine Release AR15/M4 ambidextrous Consists of 3 parts: Knob, Retainer and Arm. You...

Fits standard M4/AR15 magwells, slides in from the front, and gets retained by 2 clips in the back. Small hardware needed to mount the retaining clips. Very sturdy, the skeletonized look doesnt affect at all toughness. IMPORTANT. ... As softair...

Airsoft AEG HPA AR15/M4 Stock

Ein Einteiliger AR15 / M4 Stand im Hexagon Design. ... Er ist gut zu drucken, und benötigt keine Supports.

AR15 Magazine release for Lancer Tactical "LANCER TACTICAL M4 RIS EVO" with screw hole in the button. That's what my friends AR15 has. Resolution is just right if it doesn't fit, use 99% scale. I recommend a higher infill due the strength of the...

Its a selfmade handguard model which perfectly fit with cyma.506 AR15 model. ... You need to saw down the inner barrel or replace it to a shorter one, but you will get a perfect SMG with really much rails.

intended purpose is an airsoft arm brace which clamps onto milspec buffer tubes

Print at 99.5%.

is not perfect but it's good

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Limiter for STANAG magazine ar15/m4 -1 Rd = 29 Rd

FYI i printed AR15-main_stock.STL You can then print the latch AR15-stock_latch.STL If you want you can print AR15-stock_swivel.STL and AR15-stock_swivel_screw.STL for some more eye candy. However i haven't printed these yet and it's unlikely they...

So i modded some myself, I combined each of these https://www.thingiverse.com/thing:2805177 .223 30rd speedloader, AR15 https://www.thingiverse.com/thing:4280455 Stanag magwell profile https://www.thingiverse.com/thing:3320337 AR 15 M4 Holder...

So i modded some myself, I combined each of these https://www.thingiverse.com/thing:2805177 .223 30rd speedloader, AR15 https://www.thingiverse.com/thing:4280455 Stanag magwell profile https://www.thingiverse.com/thing:3320337 AR 15 M4 Holder...

but I didn't like how thick it was, and I did not have a spare mag release to use. So i modded some myself, I combined each of these https://www.thingiverse.com/thing:2805177 .223 30rd speedloader, AR15 https://www.thingiverse.com/thing:4280455...

Here is the extension of the hand guard I made for my G&G Rush. Printed in PLA (Don't be shy about using other materials! I only had black pla at this time.). It holds with 3 identified brackets (A-B-C) screwed on the original handguard with M3x12...

Based on https://www.thingiverse.com/thing:3086105 Modified to fit a medium/large hand comfortably (the original one didn't fit my hand quite well). Also it's designed for right handed people, but can also be used by lefties (the bottom palm support...

Snap fit for BattleAxe mags

This part was produced from this mode;

Re-designed Mil-spec stock from Grabcad. Can fit big batterys. Work-in progess, but useable as it is. ... Thank you if you support my work.

... It fits Airsoft AR15/M4/M16 magazines and should fit the real counterpart (not tested). It holds up to 8 magazines. Enjoy! ... Update 1 : The Triangular arms' front nubs have been widened to it is easier to print on standard Ø 0.4mm nozzles.

This is a wall rack created to suite nr.5 airsoft M4 AR15 Lonex plastic magazines (the 360 bb flash ones with rope in the picture).

Print the three rubberbands in TPU a95, or use the ones provided with the cheap M4 fast mag pouches every airsofter has in his trashure box. In case you haven't you can buy just the rubberbands on the internet too. for every pouch u need two M5...

This rail is designed to fit on airsoft handguards. I've tested it on King Arms and Specna Arms and it's perfect. You can mount it in few minutes via two TSPEI M5x25 screws and 2 nuts. Only work you have to drill two holes on mine internal plate.

I found multiple speedloader models available, but the one in the remix is my favorite. I really wanted a tray to dump some rounds of .223 or 5.56 to load easier. Print in imported orientation for 0 supports. Requires gluing to hold. For PLA use...

Nur minimalste Veränderungen zur alten Version dennoch vielleicht Interessant.

It works!