arducam 3d models
324 3d models found related to arducam.grabcad
Raspberry Pi camera based on drawings and measurements from - http://www.arducam.com/lowcost-raspberry-pi-mini-camera-module/
cults3d
simple protection case for the arducam. simply clips in place, but the holes are pierced. ... this model took me 5 hours to make
prusaprinters
These are the source files for my Arducam B0205 flexible mount project, please read the full story at http://www.drracer.eu/3dp/20201115_arducam Disclaimer:The attached 3MF files have been optimized for my MK3S to print fillamentum's Flexfill...
thingiverse
I bought this because it was [the cheapest solution on Amazon ](https://www.amazon.com/Arducam-Megapixels-Sensor-OV5647-Raspberry/dp/B012V1HEP4/ref=sr_1_8?keywords=arducam&tag=lsforum-20&qid=1579674962&sr=8-8) for getting a camera working with my...
thingiverse
Remixed from [Ender 3 Raspberry Pi Camera Mount by austin3dprinting](https://www.thingiverse.com/thing:3188580) and [Arducam Pi Camera Case/Holder](https://www.thingiverse.com/thing:4446024). Since I couldn't find a RPI Arducam Camera holder, I...
thingiverse
A remix of the Raspberry Pi camera case to fit the IMX519 variant of the Arducam Also added a remix of the rear cover that adds a cable chain connection, and a remix of the far end cable chain, that can be glued somewhere convenient for the chain
prusaprinters
Same sensor as in the original (v 1.3) Raspberry Pi camera, but with a proper lens. More about this camera can be found here: http://www.arducam.com/raspberry-pi-camera-rev-c-improves-optical-performance/ I bought mine here:...
thingiverse
This mount is meant to have the Arducam slipped into it. It's meant to fit MichiMiss's S1 mount found here - https://www.thingiverse.com/thing:5840909 So far, it has no issues other than no cable management, but that kinda works out anyway. ...
thingiverse
This attachment mounts an Arducam OV5647-based camera with the M12x0.5 lens to any camera bracket with 0.2" spacing. Can be run with or without the front cover as the back plate is what holds the screws. Accepts M3x10 These are available on Amazon...
thingiverse
More about this camera can be found here:http://www.arducam.com/raspberry-pi-camera-rev-c-improves-optical-performance/ I bought mine here:http://www.ebay.com/itm/281212355128?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT Print Settings...
thingiverse
... nozzle and that gets a bit tricky to make look nice. Printed without support laying with the holes on the bed works fine. M3x30mm bolt works great. ArduCam holder that I printed without the stand is here: https://www.thingiverse.com/thing:1579435
thingiverse
... She adapts according to her information to her Arducam camera. Credits : https://www.thingiverse.com/thing:4446024 A like is apreciated could help referencing! Post your Makes ! Dont forget to show my other designs ! --- Thanks, Enjoy!
thingiverse
Front Cover for Arducam. ... https://www.arducam.com/product/imx519-autofocus-camera-module-for-raspberry-pi-arducam-b0371/
thingiverse
Simple stand for Arducam ToF camera https://www.arducam.com/time-of-flight-camera-raspberry-pi/
thingiverse
I needed a very basic stand to hold my arducam for time lapse videos.
thingiverse
Industrial alike casing for: - Arducam IMX477 camera (https://www.arducam.com/product/b0242-arducam-imx477-hq-camera/) - Arducam CSI to HDMI interface...
prusaprinters
This is a remix of "RPI Cam + Arducam CSI-HDMI" by nperto on Thingiverse that rotates the attachment 90° and attaches to the opposite side. Designed to work with the arm/pivot from...
grabcad
Mount for Arducam Raspberry Pi camera on 2020 Aluminum extrusion.Use 6x M3x8, 2x M5x8 machine screws and 2x M5 T-Nuts
grabcad
This is a base to mount the Arducam OV5647 camera. ...The five (5) are 1/4-20 holes need to be taped.
prusaprinters
Case for Arducam OV9281 and similar cameras.It requires 4 4-40x5/8" screws to secure the camera inside the case.
thingiverse
Mount a K&F Concept Nano-B series Variable ND 2-400 filter 37mm to the lens barrel of a ArduCam.
prusaprinters
Changed the size of the lens hole to fit for the Arducam 64MP(https://www.amazon.com/Arducam-High-Resolution-Autofocus-)(WIP- Will upload pictures soon as this is going in my Voron 2.4r2 350^3)
thingiverse
This is 4AM Engineering's bracket for Arducam raspberry pi camera modules modified to fit Bogdanko's excellent Prusa camera mount. ...I designed it to fit my Arducam B0152 (8MP noIR fisheye) module, which is fitted to my printer's Y axis.