arducopter frame 3d models
102878 3d models found related to arducopter frame.
thingiverse
This is a full set of .STL files for the ArduCopter Quad frame and a mostly complete set of DXF files. There was a user on a DIY Drones Post offering up the open source files in any format. I simply asked for .STL. The DXF set was from a user that...
thingiverse
I haven't really been documenting the process, but initially it seemed there would be a slight weight savings in the carbon fiber/ABS parts vs the stock arducopter aluminum/acrylic parts. Maybe some different construction methods could be used to...
cgtrader
Now I think that would be silly to tell people to Print these, and buy these 'special' parts, so I am making the attempt to make this frame fully DIY...I haven't really been documenting the process, but initially it seemed there would be a slight...
grabcad
This is the 3D Robotics Arducopter Quad-C Frame and Electronics. I ordered this and CAD'd all objects based on the parts I ordered. ... I take no credit on the design process of the Arducopter, I just wanted to share this with the drone community.
thingiverse
... using my own measurements, so it is not exact to the original, but should work just fine. Instructions Print and attach to arducopter frame.. ...The screw holes are set at 3.5 mm, but may need some cleanup depending on your machine calibration.
cgtrader
I modeled this piece in maya, using my own measurements, so it is not exact to the original, but should work just fine.InstructionsPrint and attach to arducopter frame.. The screw holes are set at 3.5 mm, but may need some cleanup depending on your...
grabcad
This is a quick design for a optical flow sensor mount for the Aruducopter/Ardupilot platform. ...It is designed to be mounted on a Arducopter 3DR set up in the X configuration.
pinshape
SummaryThis is a little arm that mounts to the 1/2" aluminum arm of an arducopter and can hold the maxbotix LV series sonar sensors.InstructionsPrint it, mount the sonar sensor with two 3 mm screws Stick it on the arm and secure it with some zip...
thingiverse
I made this model a couple of years ago for the Ross School Innovation Lab's Arducopter UAV - "drone". Finally getting around to sharing it. The cost is: If you make one, share your Make. Be safe, courteous, and friendly out there. ...Print Settings...
thingiverse
This is a little arm that mounts to the 1/2" aluminum arm of an arducopter and can hold the maxbotix LV series sonar sensors. ... Instructions Print it, mount the sonar sensor with two 3 mm screws Stick...
thingiverse
I'm not a huge fan of the acrylic motor mounts that come with the arducopter kit. I already cracked one of them landing my copter in a tree. This is a one piece replacement that moves the motor inboard by 16mm so that two of the motor screws go...
pinshape
SummaryI'm not a huge fan of the acrylic motor mounts that come with the arducopter kit. I already cracked one of them landing my copter in a tree. This is a one piece replacement that moves the motor inboard by 16mm so that two of the motor screws...
thingiverse
A 3d printed replacement arm of the Arducopter from 3DRobotics
thingiverse
Quick and dirty mod for my ArduCopter Hexacopter. This is a prototype Y6 motor mount derived from http://www.thingiverse.com/thing:11604 This is basically a dual motor mount with extra thick mount platforms. The Turnigy motors that I use have a very...
thingiverse
... am working on. http://www.thingiverse.com/thing:14831 Instructions Center and put on platform in ReplicatorG and just print it. Each leg should slide right over the bottom plate of your ArduCopter.
thingiverse
Hallo hier mein erste selbst entwicklung benötigt werden nur: 12 mal 3x 20 schrauben und muttern 1xFlugcomputer Arducopter 2.8 1xMotoren von 1000KV bis 2300KV Akku etc ist klar gibt's bei Amamzon für ca 120 € Ich habe es noch nicht gedruckt werde es...
thingiverse
http://www.goodluckbuy.com/2-axis-gopro-2-3-brushless-camera-mount-gimbal-with-motor-and-controller-for-gopro3-aerial-photography-.html ) and you own an Arducopter Hexacopter...
thingiverse
Ok, so not very original, but its my take on a Quadcopter design, i have used ø12 carbon fiber tube for the arms every thing else is either 3D printer or laser Cut. Has a Go Pro Mount its runs on Ardupilot. IMPORTANT! After having quite a...
thingiverse
Holder for 2x 10mm LEDs to mount externally on your rig, used to show GPS/ARM Status Instructions Parts Needed 2 x 10mm LED's 2 x 100ohm Resistors 2 x Servo connectors Instructions Attach the Led...
thingiverse
Remove the bottom and replace with this printed part for more options to mount the controller 2 options