arduino pro micro case 3d models
300604 3d models found related to arduino pro micro case.thingiverse
A case for the Arduino Pro Micro. ...Just hot glue the sides together.
cults3d
i use this case for my "rubber ducky" (Arduino Pro Micro) i hope this helps for some people :) enjoy printing
thingiverse
i use this case for my "rubber ducky" (Arduino Pro Micro) i hope this helps for some people :) enjoy printing
thingiverse
Case for Sparkfun/Arduino Pro Micro Threading is M2x0.4 5mm Glue the Arduino in place or use some shrink tubing to press it down with the lid.
thingiverse
I saw this design from "Arduino Pro Micro A by Clevier" and "arduino pro micro with cable input by enotionz". I had to re-do the measurements mostly because their designs were to tight on the board. Even with this design you still have to sand a bit...
thingiverse
Was made for a project , the pro micro snaps into it just needs a little bit of force
thingiverse
simple snap fitted case with open Ports or not ;) ***As always, I would love to see your makes :)***
thingiverse
This is a simple case for an Arduino Pro Micro (sans pins and with a usb Micro connector as seen [here](https://www.amazon.com/HiLetgo-Atmega32U4-Bootloadered-Development-Microcontroller/dp/B01MTU9GOB). The case has an opening for the USB connector...
thingiverse
A case that holds an Arduino Pro Micro and a Cherry MX keyboard switch, with some space in between for wiring and other small electronic parts. The case is held together by four M2.5x16mm screws, but can easily be glued together. ... The code to make...
thingiverse
I created this case to fit this specific Arduino Clone (http://www.banggood.com/Pro-Micro-5V-16M-Mini-Leonardo-Microcontroller-Development-Board-For-Arduino-p-1077675.html?rmmds=search) But any similar Boards should fit The Board ist slightly...
thingiverse
This remix of [clevier's arduino pro micro case](https://www.thingiverse.com/thing:2389583) allows the use of a USB A male to Micro B adapter with the Arduino Pro Micro to implement Amplified Labs Centipede project. We are using these devices...
thingiverse
I liked the original thing, but wanted to add a mini toggle switch (as shown in the third picture) for my auto mouse clicker device. The original thing wouldn't load in 3d builder, slic3r or netfabb, but repetier was able to properly load it &...
thingiverse
This is a case I made for my Arduino clone It is a Arduino Pro Micro / Leonardo Clone board I got form- https://www.amazon.com/gp/product/B012FOV17O/ref=oh_aui_detailpage_o01_s00?ie=UTF8&th=1 I noticed there are some bright lights on the board and I...
cults3d
This is a case I made for my Arduino clone It is a Arduino Pro Micro / Leonardo Clone board I got form-https://www.amazon.com/gp/product/B012FOV17O/ref=oh_aui_detailpage_o01_s00?ie=UTF8&th=1 I noticed there are some bright lights on the board and I...
thingiverse
I was looking for a case for the DaemonBite Retro Controllers To USB Adapters, so I modified this design to fit that need. I added holes for the console cables and reduced the hole size for a snug fit on the USB cable. I also added spacers for the...
thingiverse
Case for Arduino Leonardo Pro Micro Micro usb version 3-6V PCB size 33.4mm x 18.3mm fits only without soldered connector pins! buttons: Tactile Push Button H2.0MM + 5.2X5.2MM +printed button heads I have printed all components laid on their...
myminifactory
Made this case for a project, the pro micro snaps into it just needs some force
thingiverse
This is a small case that I made to protect my arduino BS Pro micro leonardo. The print time is minimum ( it takes about 10 minutes ) and it gets the job done. ... Hope it helps anyone else and, happy hacking!
thingiverse
I am doing this mouse cos I need it, when I printed bottom part I got amazed with secret Pro Micro case, TP4056 Lithium Battery Charging Board 1A also fits gr8! Didn't do nothing to original files, just included that one and made new thing so you ...
thingiverse
This is a small low profile case for the arduino pro micro, it works great for the usb rubber ducky project.
thingiverse
A case for arduino micropro and duplicate. ...The holes and the cylinders have to be precise so print it at 0.1-0.15.
thingiverse
... 55 but should also work with any other headset if slightly modified. You'll need: 2x spring of pen 2x M3x16 countersunk screw 1x Anker Micro USB-Cable or similar 1x ED-Tracker (Arduino Pro Micro + IMU, there are plenty of manuals on the internet)
thingiverse
Small bumper case for the Sparkfun Pro micro board. ...19/06/2016 Update: added new version to correct the USB cable plugging end.
thingiverse
[ Micro USB Media Controller (Arduino Pro Micro)](https://www.thingiverse.com/thing:2967216) [Arduino Uno DB9 Case](https://www.thingiverse.com/thing:3519321) I've used inserts in the base case for M2 bolts. When asking I can create a M3 version...
thingiverse
Simple socket/casing for the Arduino Pro Micro. ...
grabcad
You can convert from USB-B type to USB-A type of Arduino pro micro and use a USB-A type device.
cults3d
Need: 4x m3 16mm 4x m3 nuts 1x m3 4mm 1x m3 washer 1x db9 1x arduino pro micro Sketch: https://github.com/armandoiglesias/g29Shifter