arkham horror characters 3d models
107273 3d models found related to arkham horror characters.thingiverse
A character stand for Eldrich Horror or Arkham Horror character tokens. I got tired of the ones that came with the game tearing up the bottom of the tokens, so I made my own that allow you to slide the token in rather than wedge it between 3 pins. I...
thingiverse
Baseplate dedicated to Arkham Horror LCG characters. Gap for card designed to fit card with sleeve with very lite friction not damaging card and neither sleeve. I made it since the ones already found in thingiverse have been with too big gap not...
thingiverse
Used to hold the character cards on arkham horror lcg (or any other card for that matter). I have printed off the 0.6mm gap stand which is a nice fit, although depending on your printer, it may be a bit tight. I have also included a 0.7mm gap design...
myminifactory
Character holder for the Arkham Horror board game! Again a piece that tend to go missing; the character holder. I also found them to be quite bad. They either slid off the cardboard or damaged it.So here is a holder that your investigator can...
thingiverse
Character Card Holder for Arkham Horror Card Game, two versions...one with a top bar, one without...top bar is not really necessary and breaks off kinda easily...printed in resin here. ... Designed for sleeved cards...if not sleeved scale it by 2mm in...
thingiverse
Replace one of the "ArkhamSpacer.stl" prints from PrintNPlay3D with six of your choice of the "Arkham Horror Character Tray v1.stl", "Arkham Horror Character Tray v2.stl" or "Arkham Horror Character Tray v3.stl" prints. ... All other trays from...
thingiverse
A dashboard for the Arkham Horror Board Game (German)
thingiverse
using original phone holder but adding Arkham Horror logo to it.
thingiverse
A gate holder for Arkham Horror and games that use the same type of gates.
cults3d
Reissue of the Arkham Horror 6cm figures with 3cm base, for PLA with better printing detail,
cults3d
Gate stand for Arkham Horror 2nd ed. will work also with gates from Eldritch Horror. ...Around the gate you can find Outer Gods symbols :)
thingiverse
Arkham Horror card storage box with dividers made for Arkhamesque Horizontal Dividers (https://boardgamegeek.com/filepage/143554/arkhamesque-horizontal-dividers)
thingiverse
... kann einfach eingeschoben werden. Die Dekoelemente verhindern das herausfallen. I uploaded this model back in 2015 on the 123dApp. This is the Link to the original Upload: http://www.123dapp.com/123D_Design/Arkham-Horror-Portal-v1-1/3889885
thingiverse
Direction arrows for use with Arkham Horror LCG (or other games that use them). ...Tried to get a feeling that would match the game.
thingiverse
Flashlight resource token for Arkham Horror LCG. replaces the resource. ... I print these will a flat bottom so they dont rule and can print horizontally.
thingiverse
Arkham Horror Encounter Cards Holder for Arkham Horror 3rd Edition. Space for six stacks of cards which is the normal amount for a game. Easy to draw a card and to be put back to the bottom of the stack. ... No support structures necessary
thingiverse
A simple holder for the Mythos- and Gate-cards in the lovely boardgame "Arkham Horror". The active environment-card can be put in front, for easy display during the game. Instructions Printed using...
thingiverse
... If you don't want to print this yourself, you can get our 182-piece **Arkham / Eldritch Horror Essentials Pack**: https://www.etsy.com/listing/599133423/arkham-eldritch-horror-essentials-pack *Update 03/13/2018* Had some issues with the original.
thingiverse
If you don't have the box, find it here: [https://www.hobbylobby.com/Art-Supplies/Storage-Organization/Storage/Artist%C2%A0Supply-Box/p/81011351](https://www.hobbylobby.com/Art-Supplies/Storage-Organization/Storage/Artist%C2%A0Supply-Box/p/81011351)...
thingiverse
Inlay for my Arkham Horror LCG with Card Sleeves in mind. Additional Info: I did add 2 Cardboard slices to fill the whole box. The Middle Inlay and Chip Box where Printed across the buildplate to fit, it barely fits on my 220x220 build plate. ...
thingiverse
This is ammunition counter for Arkham Horror the Card Game. It's a remix from another projetts. Bullet https://www.thingiverse.com/thing:1977107 I've used the cylinder from this design https://www.thingiverse.com/thing:3004363 I've rescaled...
prusaprinters
A quick little holder for investigator tokens for 2nd Edition of Arkham Horror, or any other FF games using the same cutting template. If you have THE artist box from Hobby Lobby, this fits nicely into the larger bottom sections. If you don't have...
thingiverse
This is my solution for Arkham Horror 3rd edition that I have been using for some time now. It is designed for sleeved cards and has enough room to grow for a future expansion or two. Details and Printing Counts ----- - 1x Assets. This is a nice...
thingiverse
First and foremost, inspired by: http://www.thingiverse.com/thing:15170 These holders are sized for the Arkham Horror Mythos and Item card sizes. They use a locking pin instead of a tab because I wanted these holders to fit inside my organizer box...
thingiverse
This is a two part design (print 1x bottom and 1x top) inspired by the deck boxes by BoardGameXtras which is designed to store player decks they also transform into draw and discard holders when playing Arkham Horror the card game. I printed two...