armattan chameleon ti 7 3d models
209476 3d models found related to armattan chameleon ti 7.thingiverse
Piece for Armattan Chameleon TI 7´Long Range + GPS bn-880
thingiverse
I took 3 of the the awesomely designed Gorpo mounts for the Armattan Chameleon and added a reverse angle to bring the Gopro to a 25 deg tilt. Prints great using TPU, 50% infill. The original design has a great slit by the lens that lets you easily...
cults3d
A smart way to mount you're crossfire reciver in the front of the frame to save some space in the rear
thingiverse
Simple TPU mount for the caddx turtle to sit in the front of a Chameleon Ti LR 7" held snugly on the two supporting standoffs. ...With a flap to protect the sd card.
thingiverse
Designed my own Mount like always... ...28° Camtilt like my GoPro Session mount for the Chameleon TI/Rooster, i think with 28° it will be perfect for some nice cinematic footage or freestyle shredding ;) 0.15 Layer 40% Infill Supported
thingiverse
Mount for gopro hero 7 in the armattan rooster and chameleon frames
cults3d
Mount for gopro hero 7 in the armattan rooster and chameleon frames
thingiverse
So i found some on thingiverse and modified them to fit Armattan Chameleon Ti 7 inch. The first file is a holder for the matek m8q - 5883 GPS. And it has a holder for the SMA connector to your FPV antenna. At the bottom you have a holder for the...
thingiverse
Prop Guard for Armattan Chameleon TI 7 inch. Matching landing feet can be found here. ...https://www.thingiverse.com/thing:4754351
thingiverse
This is a remix of https://www.thingiverse.com/thing:3816327 I created for use with my Armattan Chameleon Ti LR 7 inch DJI Edition quad build at https://rotorbuilds.com/build/24835 to hold the DJI Air Unit.
thingiverse
This is a remix of https://www.thingiverse.com/thing:4571701 I created for use with my Armattan Chameleon Ti LR 7 inch DJI Edition quad build at https://rotorbuilds.com/build/24835. ...This remix extends the DJI Antennas and adds a GPS holder.
thingiverse
Click this thing into the Armattan Chameleon Frame and you can put RX, Hellgate Buzzer etc. ...between FC-Stack and Antenna Mount without the need to fix everything.
thingiverse
Armattan Chameleon Ti Antenna Bracket Ver1: 3mm thick Ver2: Adds 2mm thickness to the antenna portion. ...
thingiverse
simple xm plus holder for the armattan chameleon ti. ...holds pretty well even in hard crashes
thingiverse
This is a bottom mount battery/frame protector aero skid, for the Armattan Rooster / Chameleon Ti. ... And some arm Boot's, slip on's!
thingiverse
Gopro mount for Armattan Rooster / Chameleon TI with 27° tilt and more space for your lipo. Holded by the cfk plate. ...I used 50% infill with a 0.2 resolution.
thingiverse
Chameleon TI Accessory Kit: This is a full package for the Chameleon TI (Some parts have Rooster compatibility also). The kit contains: - Front and rear Wire Guards designed to work with individual ESCs and PDB setup - Front Wire guard with built...
thingiverse
Here is a new design for a platypus tail that fits onto popuar Armattan frames such as the Chameleon or Rooster. It is designed to hold the BN-880 gps away from noisy electronics so you don't have to install a mast. This design also holds an Immortal...
thingiverse
Rear antenna mount for Armattan Chameleon Ti. ...Only works if you use short batteries.
thingiverse
VTX antenna spacer, it fits perfectly on the back of the Armattan chameleon TI Material: TPU https://youtu.be/AvMS2CGmjGo
thingiverse
RunCam Micro mount for the Armattan Chameleon Ti. ... Its possible to set up every angle with a 1.8 lens ;) print with TPU / PLA / PETG everything works fine
thingiverse
Antenna Mount and Protection for Chameleon Ti
thingiverse
I made this personally for my Armattan Chameleon Ti using my Gopro Hero 3 and Gopro Hero 4. If you have the waterproof cover for Gopro, unscrew the lens cover and put it inside the case. ... *reuploaded
thingiverse
Here you'll find two TPU prints for your beloved Armattan Rooster or Chameleon Ti frame: - a 35° tilted, unbreakable GoPro Session mount, - a dipole VTx antenna mount, compatible with all TBS uFL dipole antennas and other similar designs. This mount...
thingiverse
I designed this to convert my Armattan Chameleon Ti Frame to accept a HD DJI FPV Air Unit and camera. I designed this for a TBS Immortal T antenna for Crossfire. Printing: Parts all can be printed with no supports For strength I printed at...
thingiverse
Chameleon Ti GoPro Hero5 Session Mount. Designed to be printed in TPU. ...Rigid materials will not work.