arrma rc 3d models

We're excited to announce the introduction of an additional wing option for the Typhon 3s and 6s. ...This innovative design is printed using TPU (thermoplastic polyurethane) with a minimum hardness rating of 92A, ensuring durability and flexibility...

Saw the Typhon wing on here; printed it for my brother, but he said it was too narrow for his taste. ...I designed this one to be about an inch wider on each side while maintaining a race car look.

cut out window, paste piece in place.

After my first maitnance I noticed that the motor was hitting the chassis. It was a little scratched. So I decided to model a small support for the motor. This is held in place by cable ties. I haven't run it yet, but I think it should help. ...I...

FPV Camera Mount that uses factory front body pins to hold. ... Thing in Progress

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/7AdOyeytrOV

A simple adapter to use two 35mm fans on Talion EXB. ... the fan guard with spektrum logo you can find here: https://www.thingiverse.com/thing:5400591

This is exactly as requested. ...Measurements are multiplied by 1.0154 to accurately compensate for ABS shrinkage.

Remixed Typhon 3S Wheel Hex Covers to work on Hoons The originals were too large to fit inside the centers of the Hoons Slimmed them down a couple millimeters and there we go I printed them in this flashy red glitter PLA to mimic the red...

cut out the inner shape of the scoop out from the typhon body in the areas shown. glue from inside. ... adds airflow inside the body for better cooling.

This is a stronger small front bumper for bashing. Indented to fit under the car and mount with all 4 bolts. You might have to drill out the whole just a bit for the bolts but mounts flush to the front covering the pins and offering extra protection...

Based off the motor support by hyperion917 on Thingiverse I wanted to make some changes to both for printing and function improvementI got rid of the tab for the 4mm screw so it could print flat and made a new way for the zip tie connection to work.

Broke the front section of the driveshaft after a big hit. Performs extremely well, no issues after several hours of hard bashing. Designed to work with the original spring. Slighlty shorter to make removal a bit easier. Get your tolerances...

<p>Need to drill two holes on the stock side shield to attached, or just glued.</p>

Print this wing mount with flexible filament. You will need two longer M4 screws. ...

Humans often find it necessary to make precise holes by carefully heating screws. To accomplish this task, one requires a mirror object that can be positioned on both sides of the screw. ...The following settings must be specified in the print queue: 1...

<p>For higher strength, place the model on a hot bed as show on the picture.&nbsp;<br>I recommend durable material, for example nylon, abs…</p>

Armored Raider Rear Shock Brace Prints Quickly Using K8200 Printer. Settings Are Set for Fast Printing. Printer Selected Is the Reliable K8200 Model. ... Infill Percentage is Optimized at 10 Percent for Lightweight Strength.

My body mount broke so I made this so I can replace it on a much faster time scale

The printer is currently set to a default configuration. To initiate printing, first adjust the infill percentage on the control panel. The current setting of 10% infill can be increased or decreased as needed for optimal results. ...Note that the k8200...

Daul 40mm fan cover.

I didn't want to buy the wing washers so I designed this. I Have bashed it a couple times now and holds up great. ...60% infill with 4 walls are the only parameters I change from my normal print.

I remixed those mudguards to remove the EXB logo who is neat but also grabs dirt :-) Thickness: 2.4mm (thicker part) Please like if it's useful for you :-) It convince me to upload more if I see people uses my things.

The stock tray is very tight if you use a 2S battery and it scrapes the battery wires substantially.  We like the Spektrum SPMX50002S30H3, and this tray is sized to fit it snugly so it doesn't move around, while also giving a bit more clearance by...

A remix of the original by schneidp20, thank you. as suspected by the author too soft with TPU so added a middle section to stiffen the part. having tried many fillers this one gives the same stiffness as the stock part. Print with 20% gyroid...

Human: fine-tune holes by warming screws 1x mirrored object for both sides Print Settings: Printer: K8200 Rafts: Irrelevant Supports: Unnecessary Infill: 20%

VERY SIMPLE PRINT. PRINTS IN 3 PIECES AND SCREWS TOGETHER WITH M3X8 SCREW. ...PRINT EACH PIECE FLAT WITH NO SUPPORTS.

I'm having trouble understanding your request. ...Could you please provide more information?

Need to drill two holes on the stock side shield to attached, or just glued.

This is a WIP and will receive updates this works with arma vorteks and granite it slots into the circle indent on the bumper and go's under the Body