arrow nock 3d models
9154 3d models found related to arrow nock.thingiverse
This is an archery arrow nock. ...It fits my Easton XX75 1916 arrow shafts with a little post production.
thingiverse
Arrow nock i made from scratch hope you like it plz comment below on what i could improve on it
thingiverse
This is an arrow nock for 5.5mm shafts. Added another stl for 8mm shaft. ... Instructions This may be stronger printed on it's side with support.
thingiverse
Arrow Nock 4.2mm. To scale, use the DWG file. I have not tested it yet. ...Let me know if it works
pinshape
WARNING use at your risk this is untested and NOT guaranteed to be safe especially with stroger bows. This is an arrow nock for dowel arrows. Do NOT use a taper tool. I made this for a pencil sharpener, sharpen until the dowel fits. ...Print at 100%...
thingiverse
Arrow nock. I've printed it at a 0.1mm layers and dropped speed to 10mm/s with 35% fill will test it on a low powered bow 1st and then maybe my 20# recurve. ...More Archery posts in my group http://www.thingiverse.com/groups/3d-toys If you want to see...
thingiverse
... arrow and works great with the bow. Feel free to share or remix this design. Be sure to check it out on myminifactory: https://www.myminifactory.com/object/3d-print-arrow-nock-94549 Please share your thoughts or suggestions in the comments. ...:)
cults3d
Sometimes on our archery practice the nocks jump from the arrow when hitting the target. I usually can't seem to find them nowhere, so i decided to design my on nocks to print them when i lose one. From the safety point It's always better to buy...
thingiverse
This is a nock for carbon arrows with a diameter of 5.6mm. I tested it with a 26lbs Bow (30lbs on the hand) and it works perfectly. ...
thingiverse
Sometimes on our archery practice the nocks jump from the arrow when hitting the target. I usually can't seem to find them nowhere, so i decided to design my on nocks to print them when i lose one. From the safety point It's always better to buy...
thingiverse
The Nock on my son's arrows kept getting broke from use. Rather than ordering parts, I used my Ender 3 and TinkerCAD to come up with a solution. This fits in the arrow and glued in. I used rubber cement in case I needed to pull it out to replace it.
myminifactory
I have bow and arrows, but they're quite old, and one problem is that the nocks keep breaking off (the nock is the part that clips onto the bowstring, I didn't know that until I googled it). I decided to design a piece that could fit over the broken...
thingiverse
After breaking the nock (the piece that keeps an arrow on the bowstring) on a steel arrow I had, I designed this. I'm not an expert on archery, so you may need to do a bit of scaling to get just the right fit. ...If you want the part to keep up with...
thingiverse
This is a great little part which will save you a fortune when buying new nocks for your arrows. They work really well when made from Carbon Fibre Filament, use 2 shells and 100% infill to make it durable. 3Dynamic Systems Carbon Fibre Filament...
thingiverse
remove all remaining glue attached for me, it worked out fine at a 101%, without any need for glueing Even I know there already are a lot of other nocks around, ....in my case (schaft a little scattered at the end) this works better for me, maybe...
thingiverse
This was a 1 minute arrow nock design for a kids bow and arrow set my wife got our grandson at Dollar General. The arrows had no nocks so after some teaching he was able to use the arrows but I thought a nock would help. there are better designs out...
cults3d
4 Arrow Nock Types: Symmetrical (normal (green), wide (red)) Asymmetrical (normal (green), wide (red)) SCALE At 100% scale the nock dimensions are: Length overall: 28 mm (1.102 in) Length outside: 16 mm (.63 in) Fits all .246 shafts and bushings...
thingiverse
This is a wide notch arrow nock. It is made to be printed by an FDM printer on the flat side. Print two to make a complete nock. Due to the shape of the nocks notch, the notch acts as a tactile guide as long as the length of the nock is not much...
thingiverse
Features: Fully parametric so will fit your arrow spine and bow string perfectly Rounded cutout to aid arrow placement on string Bump to find what arrow side should point away from the riser when the arrow is nocked to the string Protrusions to...
thingiverse
This is a simple arrow nock, based on the g-nock diameters Print it with a layer height of 0,08mm or 0,12mm to get optimal stability.
thingiverse
Arrow nock for 7mm diameter arrow. Nock hole is 7,2mm diameter and it fits perfectly on my printer to 7mm arrow without glue and is almost impossible to take off. ...
thingiverse
arrow nock for cobra r9/adder 7,5" bolts the size fits perfectly, so just apply a bit of glue to fix the position use ABS Update: you can buy good quality nocks for Corbra Adder/R9 from Aliexpress https://s.click.aliexpress.com/e/_ADW1dL no need to...
pinshape
An arrow nock for kyudo that fits into a 1913 size tube. Printed and tested in PETG. Notes (will update after more use): - supports cause a really ugly surface on my printer, which I don't know if it's normal or just my lack of skill. -...