asetek 645lt 3d models
46 3d models found related to asetek 645lt.thingiverse
This cap is a design by me, that snap fits on the Asetek 645LT cooler to hold a TURZX 2.1 inch USB internal display. It dont need any glue to hold, its a very tight fit. ... I printed it with resin and support, sanded it a little and painted it black,...
thingiverse
Asetek Wheelbase Powerbutton baseplate without the mounting holes. ...Perfect for clean installation with doublesided tape etc.
thingiverse
Major Hardware x Asetek AIO Pump Cap Challenge Submission. ...Formula 1 wheel nut inspired AIO Cap.
thingiverse
remix from Leoxz DDU 800 mount for Asetek simracing wheelbases. Suited for every dashboard. Use double sided tape to position. ...
thingiverse
remix from Leoxz DDU 800 mount for Asetek simracing wheelbases. Suited for every dashboard. ...Use double sided tape to position.
thingiverse
Project: https://simracing-pc.de/en/2022/06/13/diy-project-new-end-stop-for-the-asetek-invicta-pedals/ Discord: https://discord.gg/V5ZKUj3weJ
thingiverse
Asetek Rumble motors, please see photo as how they fit, 2 bolts and nuts needed to secure to pedal No supports needed, print on flat face
prusaprinters
Asetek Rumble motors, please see photo as how they fit, 4 bolts and nuts needed to secure to pedal.Pedal plates must be mounted one hole higher!!!No supports needed, print on flat face
thingiverse
Asetek Rumble motors, please see photo as how they fit, 4 bolts and nuts needed to secure to pedal. Pedal plates must be mounted one hole higher!!!! ... No supports needed, print on flat face.
thingiverse
Needed a smooth foot plate for my Asetek Simsports forte pedals, that was more gentle to my feets when driving without shoes. Also two clips/holders to keep it in place. You might wanna design you own since these works with a wood plate. ... I...
thingiverse
... M5/20mm countersunk hex bolts used and M5 Nylock nuts used. Printed with Gyroid for added strength on the right side The Asetek have super light throttle springs so I have made these with a minimal thickness as to not use too much filament.
thingiverse
Are you tired of seeing the exposed wires on your 1000€+ Front mounted Asetek Wheelbase? Me too. So heres a simple Print to cover them up. It is one piece and doesnt need any support. I decided to give them a 90° corner, so that the cable can...
thingiverse
Asetek Invicta Clutch pedal smooth pedal plate These make the pedals sock friendly or nicer for someone that wants a smooth pedal Uses 2 countersunk bolts (will need to be sourced) and nylock nuts to hold into place. ... Print upside down so that the...
prusaprinters
Asetek Invicta Clutch pedal smooth pedal plate These make the pedals sock friendly or nicer for someone that wants a smooth pedal Uses 2 countersunk bolts (will need to be sourced) and nylock nuts to hold into place. Print upside down so that the...
thingiverse
Heel Gap Remover for the Asetek Invicta S Series. Just stick it down with double-sided tape. ... Its the same for throttle and break.
thingiverse
Project: https://simracing-pc.de/en/2022/06/13/diy-project-new-end-stop-for-the-asetek-invicta-pedals/ Discord: https://discord.gg/V5ZKUj3weJ
thingiverse
Project: https://simracing-pc.de/en/2022/06/20/diy-project-alternative-pedal-plates-for-the-asetek-invicta-pedals/ Discord: https://discord.gg/V5ZKUj3weJ
thingiverse
A Mounting Plate for Asetek Wheels / their type of Quick Releases. The holes are 40mm apart, so that you mount it on a horizontal 80x40 Profile. ... Intended Screws are M8 x 15mm cylinderhead screws
thingiverse
I needed a wider speeder pedal for my Forte pedals from Asetek. I also needed it to be more sock friendly by only having two holes for screws and with less sunken. Can also be used for brake. You can mirror it in your slicer if you want it...
thingiverse
... not work for you. ... Print upside down so that your pedal plate is nice and smooth M5/20mm countersunk hex bolts used and M5 Nylock nuts used. Printed with Gyroid however the Asetek have super light throttle springs so not much infill is needed
thingiverse
Here is a reverse engineered Version of Aseteks Quick Release for custom wheels. It has very little to no play and is rock solid. You'll need 2x M3x15mm Bolts for the lever and i used a 8 x 20 mm spring i had lying around from an extruder upgrade....
thingiverse
Asetek compatible bracket for GPU cooling. ...Similar to the NZXT kraken bracket except this is made of plastic.
thingiverse
A gap remover for the Asetek pedals, added a second file with the extension of the banked part of the heel hold. ... V1.1 is 1mm wider to prevent moving up(rotating)
thingiverse
This is an adapter that allows you to take cheap Asetek-designed CPU AIOs (i.e. NZXT, Corsair, etc) and screw them onto an AMD GPU with a 53mm-54mm hole spacing. AMD has been using this hole spacing for most of their high end GPUs for about a decade,...
thingiverse
... and SF750. Its slightly higher than the PSU Bracket of the Loser Card Mod but it still fits with the Asetek 645LT AIO. Installation is a bit tricky but you will get it. ...Its easier if you losen the screws of the spine and put everything in.
prusaprinters
<p>After making the smooth and wider throttle pedal plate I was asked to design the brake one too.</p> <p>I have make the plate a little thicker to compensate the extra braking pressure</p> <p>This like the other plate I made would take the M5...
thingiverse
After making the smooth and wider throttle pedal plate I was asked to design the brake one too. I have make the plate a little thicker to compensate the extra braking pressure This like the other plate I made would take the M5 countersunk hex...
thingiverse
This design is a simple adapter for mounting a Asetek 4th gen to a 1660 Super. In my case I use a 1660 Super from Asus, the Pheonix version that have an awful cooler. Before this change on an open bench it did hit the thermal limit and drop down the...