astro x x5 3d models
327515 3d models found related to astro x x5.thingiverse
I designed this mount to be used the Astro x5 frame to keep the antenna placement nice and neat....
thingiverse
This Gopro mount was originaly design by thingiverse user: wrong17 but it was made for a cinewhoop (squirt v2) and I wanted to used is for my Astro x5 so I design a new adaptor. Just need to slide a 20mm stand off inside the mount and use 3m...
thingiverse
Immortal-T antenna for JohnnyFPV Astro X5 or Mark4
thingiverse
This a TPU Arm bumper to protect your frame adapted for the Stretch X5 V2 or Astro X5 jhonny fpv frames. -If you have a Bowden printer you might have to do some upgrades to print TPU. -You might have to adjust the holes to fit your frame...
thingiverse
TBS crossfire holder for Astro X5 JohnnyFPV frame
thingiverse
Astro X5 Johnny FPV Hero 7/6/5 Mount 30 degrease Print in TPU If its too big when importing scaled down to 10%
thingiverse
Astro X Gopro Mount Base TPU There are Two Versions One is Shorter version & Other one is longer version
thingiverse
25 Degree Mount for the AstroX x5 frame, this mount is perfect for Hero 5 and 6. ... Soft Filament only, mainly TPU, NinjaFlex may work too though
thingiverse
Based on Astro-X frames I created this one for fpv freestyle. I would highly recommend you to soft mount your FC 'cause of the direct coupling with the Arm, that could cause and transmit vibrations. For those, wo have integrated ESC's, the thick...
cults3d
Based on Astro-X frames I created this one for fpv freestyle. I would highly recommend you to soft mount your FC 'cause of the direct coupling with the Arm, that could cause and transmit vibrations. ... For those, wo have integrated ESC's, the thick...
thingiverse
This a TPU front bumper to protect your FPV camera adapted for the Stretch X5 V2 or Astro X5 jhonny fpv frames. -If you have a Bowden printer you might have to do some upgrades to pint TPU. -You might have to adjust the holes to fit your frame...
thingiverse
... it will work with most any TPU skin or silicone skin case (pictured, pink). Required: - 2x M3 15mm/16mm screws (recommend panhead, hex) - 2x M3 nut - 20mm x 200mm lipo velcro strap or similar - GoPro Session4/5 Runcam3 or Foxeer Box plus case
thingiverse
Bracket to align the X Axis. ... Just print 4 of this, and use M4 x 12mm screws. ... If the structure of your printer is straight, the axis will be aligned correctly using this.
thingiverse
Astro X Solid Top Plate with fin for turtle mode. Top plate thickness is 3mm. ...Best printed in TPU.
thingiverse
For astro true x For flexible filament Can use tattu r-line / infiniy 90c / GNB. ...And might can use other 1300~1500 lipo battery(width 36mm)
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: bar_thickness = 2.4 outer_margin_width = 1 borderextruder = extruder2 bar_shift = 0 font_weight = 0 font_size = 12 writing_direction = ltr...
thingiverse
these are replacement parts for the main X-Y carriage mounts, I have noticed with my Tronxy-x5 that isn't even a month old cracks appearing along the belt locks around the bearing carrier and where the 8mm rods go in, so being a firm believer in...
prusaprinters
Mount for Meilan X5 Turn Signal light onto Kestrel Talon X (55cm).Printed PETG, 0.2 Speed using 0.4 Nozzle.20% Infill, Grid (others may work better). It fits a bit snug, but should be fine reusing the existing Meilan Mount and screws.About 95mm...
thingiverse
Mount for Meilan X5 Turn Signal light onto Kestrel Talon X (55cm). Printed PETG, 0.2 Speed using 0.4 Nozzle. 20% Infill, Grid (others may work better). It fits a bit snug, but should be fine reusing the existing Meilan Mount and screws. ...
thingiverse
Quest X5 replacement coil hinge Print in PETG or other strong(er) material. Print with 25% or more fill, no supports are needed. Grind off the existing (broken) flanges and use an epoxy (or similar) glue to bond the new hinge to the spool. ... Printed...