asus vx 239 3d models
3757 3d models found related to asus vx 239.pinshape
SO-239 usually come as a wall mount connector. ... I needed one for my rg-58.
thingiverse
This is a combination mount and holder I used for mounting an SO-239 based 1/4 wave antenna in my garage rafters. The hole is sized so that a PL-259 connector can pass through it. I am using it to both route cable and hold the antenna upright. ...The...
thingiverse
Vx-800 camera holder adaptation for https://www.thingiverse.com/thing:5526397/. ...
thingiverse
Four M3 screws, four M3 washers, and four M3 locknuts is the hardware I chose to use to attach the so-239 to the bottom mount. Used three different sizes of EMT conduit. 1/2, 3/4, and 1 inch. Used nominal sizes of the outer diameter of the pipes...
thingiverse
its probably already been done....but as a ham radio op I need to work with chassis mount SO-239 connectors....not having found a decent simple template to cut or add to my projects I modeled up the connector I have and have tested it and it fits...
thingiverse
... are not mounted yet. Just put the thing on the back of a SO-239 chassis mount to make it more pretty and give you a mounting option. ...The little hole on the side is to fill the inside with a resin or something like that to make it watertight.
thingiverse
con una batería recargable del tipo 14500 y un resorte, recupere mi viejo y querido YAESU vx-1. ...Un poco de lija fina es necesario.
sketchfab
ID no. ...MN/AH/63 “Exakta Varex VX Camera” Museum: The Museum of Niepołomice — the Niepołomice Royal Castle http://muzea.malopolska.pl/en/obiekty/-/a/26891/1126982 Digitalisation RDW MIC, Małopolska’s Virtual Museums project
sketchfab
Based off the YE-4 gunship from SWG This vessel was developed from blueprints for the VX-9 Mailoc which were acquired by the Republic SIS and freely distributed to Republic aligned companies. The VX-4 Preserver in specific was designed by Republic...
thingiverse
This is a simple webcam stand i made for my microsoft lifecam vx-1000, but I guess it fits all vx-series webcams. I use it to monitor my 3d-printer. It is simple and effective. The part between the bottom and top part is a 8mm rod with a length of...
thingiverse
Support remixed from https://www.thingiverse.com/thing:2459051 to work with Microsoft's lifecam vx-1000 camera, which I had dropped and re-used when I purchased Ender 3, edited the file on Tinkercad and ready !!! ...I put together with the handle that I...
thingiverse
A 230 mm extender tube for Dyson Vx series. It can either replace or extend the supplied long tube. The connection adapter for the vacuum cleaner side is base on this design: https://www.thingiverse.com/thing:2424881 When printing be sure...
thingiverse
GoPro chin mount for Scorpion VX-15 helmet. You should use some quality double-sided foam tape to fix it to the helmet. There are also strap holes so you can further secure it. Version 2: The model is split into two parts which can be connected...
thingiverse
A short Ender VX-500 introduction video: https://youtu.be/XiqcePzt0X8 A short video on the operation / cleaning of the Ender VX500: https://youtu.be/aMUB5sEuJ2U A detailed protocol on the use of the Ender VX-500 machines:...
thingiverse
Added a mounting hold to the back so it can be used with this thing, https://www.thingiverse.com/thing:2516411 Should work with most Microsoft VX-xxxx models that had that rubber boot leg thing. To take it apart, 1. pop the silver ring off, its...
thingiverse
I made a mount for the Microsoft VX-200 life cam using the ball on the bottom side of the camera. to attach to my redesigned camera mount for the Makergear M3 https://www.thingiverse.com/thing:5841413 The ball on the camera is 7.45mm DIA. This...