at2020 mic stand 3d models

This stand although bulkier to print, does include the threads for the microphone. I may update it to a slimmer version in the future. Also, I took the monster holder into 3D builder, sliced off its end, and fused my piece onto it in an ugly...

The model consists of three parts, the “cup”, where the microphone sits, the “legs” which connect to both the cup and the stand, and the stand, which holds the legs in place.Can be assembled easily, you need m3 screws - they should self tap. ...no Nuts...

Very simple Mic Stand for Audio Technica AT2020. ... I have the XLR version, should be fine for USB too - plz check the inner diameter.

This is a simple knob replacement for AT2020 included stand mount made with Tinkercad.

Simple AT2020 Microphone Stand. Fits neatly on my desk and out of view of the monitors. ...Has a 30° angle tip, so it doesn't knock over all too easily.

Comes in two versions: 7mm depth (the pop filter is 7mm away from the microphone) and 1inch (the pop filter is 1 inch away from the mic). The 1 inch version is more effective at removing pop sounds, the 7mm is more minimalistic. ...Both versions are...

I didn't like the original stand as it takes up too much space so I designed one. You need a 18mm or 20mm M3 screw and a nut to secure the top pieces. I printed it with tree support, 30% infill, 3 wall layers, 0.28mm layer height, 50mm/s. ... I...

My audio technica AT2020 condenser microphone didn't come with a holder for a mic stand so I created one. It should fit other ones as well -Inside diameter is tapered from 50mm to 52mm. I used the other half of the old dynamic mic stand holder that...

Remix from https://www.thingiverse.com/thing:3619421 Changed design of feet and angle of mic.

Simple Mic stand for my Audio-Technica ATR-2500.

this stand is compatible with all the standard mics

Mic stand for Silvermonkey/Sudotack Anet A6 modded ABS 250*C h:0.25mm Total: 2h41min

Stand for microphones - I use an AKG p120, but most mics using the industry standard 5/8"- 27 threading should work. ...The black adapter in the picture was supplied by the manufacturer along with the microphone.

This is a very simple tabletop mic stand. Idk how tall it is, or if it actually works. Support material may be needed. I may come out with a new better one soon. ...Hopefully.

A mic stand which can be pieced together with a PCB pipe and some M8 screws. It is designed to be modular and foldable so that it can be put away in a corner or under the desk. I designed it to be used mounted to a computer desk for a mic with an...

A quick anti roll device for a MIC, I made this for one of our caretakers from the council for there mics so they when people put it down on the table it did not roll away

Desktop microphone stand; one-piece

I don't have a lot of money, but have been able to use a camera mic for some recording. No designs that I was able to find supported that particular mount. Enter my design: it's simple, elegant (in my opinion), and fairly easy to print. ...

I don’t know how many of you have a microphone like this, or more specifically the stand that it uses… But i’ve found the factory stand to be quite large and intrusive. So I’ve made a smaller simpler base for the stand. There’s a simple model...

I needed stand for quite heavy microphone (PC microphone by Tracer with fancy “cage” suspension). It has 6mm wide tab with a hole that accommodates M5 screw - so it was chosen as stand's “interface”. FreeCAD project file is included so if you need...

This is a mount for the Audio-Technica AT2020 to add a pop filter on the stand mount. This should work for the AT2020USB too because it appears to come with the same stand mount. All you need to do is take the screws off of your pop filter then pry...

Mic Display Stand

Modular mic stand with clamp

Headphone hook for a mic stand

Adapter to fit a usual dynamic mic to fit into a standard condensed mic stand.

Remixed a headphone stand to hold an Icom mic

Daughter wanted mic stand for her Barbie/OMG dolls

Mic stand adapter for the B105d & B205d speakers.

HotShoe for a Boom Mic. ... 90 degree or 45 degree Just place it on your mic stand or light stand

Mic Stand Cable Clip for the small part of a mic stand. ... Works on 15mm diameter tube which on some mic stands is the upper part and the boom.