atom v2 3d models

This mount was designed to be used with the stock Rotor X Atom V2 Camera with the 110 Lens. Other lens's may fit, but cannot guarantee anything. It is designed so that you can screw the lens into place. it can also be cut down the center through...

... go get it more robust. If you wish feel free to print it in one piece. After Print is finished, snap it in your Atom V2 hood and glue it in place. ...To install the hood with antenna protector you have to remove the shrinking tube from the antenna.

I made this Thing to protect my Whip antenna. v2.0 now the antenna fits with the shrinking tube for more protect to the antenna if the canopy is removed Print instructionsCategory: R/C Vehicles Print Settings Printer: CoreXY Rafts: No Supports: No...

Summary I almost cut my motor wires with a bent prop on my atom V2 after a crash. To protet the wires from the props I created this light weight guard. It is designed to be made out of TPU or Ninjatek Armadillo or Cheeata filament and simply clips...

I almost cut my motor wires with a bent prop on my atom V2 after a crash. To protet the wires from the props I created this light weight guard. It is designed to be made out of TPU or Ninjatek Armadillo or Cheeata filament and simply clips onto the...

The screws and the Atom V2 canopy hold everything nice and tight even with the slice in the mount. Huge credit to Drew Price (TenFPV) for doing the bulk of the design work on these!!! ...Print Settings Printer: FlashForge...

Designed a mount to attach my GoPro Session to the Atom v2. This includes both a framed mount and an unframed mount. The unframed mount will work on the session with or without a case and should support other cameras as well. Print with supports. I...

The atom ring v2 is a modern piece of jewllery to match the atom bangle:https://www.myminifactory.com/object/17099, or the atom bangle v2:https://www.myminifactory.com/object/atom-bangle-17696.V2 has been change to look more like the atom bangle.

**Please consider supporting our Patreon page to enable us to develop and release more awesome designs in the future https://www.patreon.com/airbladeuav** I redesigned the RotorX Atom Mini V2 from the ground up based on the bigger and more popular...

Cartoon Atom v2 005

Cartoon Atom v2 002

Cartoon Atom v2 001

Cartoon Atom v2 004

Cartoon Atom v2 006

Cartoon Atom v2 003

I managed to make the Runcam Swift Micro fit in an Atom V2. I based the model on the V3 mount, but recreated it in Sketchup. I went for 30 degrees tilt. Sketchup files are included if you would like to try to change the angle. The swift micro model...

I made a cable saver for the RotorX Atom V2 to keep the power cable from being cut by the frame and shorting. I had to widen out the zip tie holes a bit with a small screwdriver. ...Print Settings Printer Brand: LulzBot ...

Printed with ABS Layer height 0.25 Frame weight: 10g You will be needing four 1.4x5mm screws to put this frame together

Unusual modern design bangle, printed in PLA, 0.22 layer height without support. ...Better fitting than V1.

Customized version of http://www.thingiverse.com/thing:114247 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=114247 Instructions Using the following options:...

Summary UPDATE: Added a version to use with a crossfire micro rx. Make sure you run the RX antennas before you install the axii u.fl antenna. UPDATE: 8/13/17 Revised the mount to accommodate for prop flex and clearance. Designed this mount to use the...

UPDATE: Added a version to use with a crossfire micro rx. Make sure you run the RX antennas before you install the axii u.fl antenna. UPDATE: 8/13/17 Revised the mount to accommodate for prop flex and clearance. Designed this mount to use the...

Fits all RotorX Atom frames like a glove, including v1, v2, 2.5mm and 3mm. The top bumpers are for the top carbon fiber plate of the v1 only. These have been optimized for print quality...no more stringing or supports needed. I designed these for...

These are a 26mm Wide wheel designed to replace the "Atomic" wheels, these work with the readily available WLToys A212-0 Tires.

I wanted to mount my M5Stack Atom Matrix on top of a camera. So i had a friend work something out for me. I have since refined it with a screw and nuts to fit into a hotshot without any screws or other equipment. the bigger nut locks it in place...

This is a modification to Atomic Pi Case for Single Board by skelman The following modifications have been made: Bottom part scaled so that there is more space underneath for wiring etc. ...(18.68 mm compared to 16.6mm) Top part: Added slits for Wifi...

This is the Version 2 of my customizable atomizer box ( Version 1 : https://www.thingiverse.com/thing:2025553 ) Box Description : This little box allows to store an atomizer for ecigarettes. As it is customizable, you will be able to build one that...

... the Sub Atomic kits. ... V1 Rings fit Sub Atomic kits shipped with the Black camera guards V2 Rings fit Sub Atomic kits shipped with the Silver camera guards -Gnarlyfpv Print with the flat side down. Support the 1 overhang. ... TPU 100% infill

Stand is about 175x135x22mm - Holds up to 3 atomizers [<=30mm], 9x 10ml Liquids & other small items. ... Print how ever you like.

Customized version of https://www.thingiverse.com/thing:1298948 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1298948