atomrc f405 3d models
326 3d models found related to atomrc f405.thingiverse
F405 wing FC mount and gps mount for Vortigaunt wing from E-wings.
thingiverse
Simple top-loading mount for the Matek F405-Wing. ... 2 files, with and without mounting holes.
thingiverse
This is a holder for a matek f405 wing board which you can either screw or use the anti-vibration dumpers to fix inside of your plane.
thingiverse
A flight controller mount for the Matek F405-Wing board. Holes in the bottom to allow mounting to standard 30.5mm holes. Top plate screws down to hold the board in place. ... All aspects of the board are still accessible (A new top cover design will...
thingiverse
This is a protection plate for your Mamba F405 Flight controller. But you have to keep in mind, that theres an additional 10mm spacer (standoff) mounted on the stack. In my case there's a TPU plate with VTX and RX assembled on the top. So you have...
prusaprinters
Simple mount for the F405-Wing Flight Controller. I found several designs, but in my opinion they were all to clumsy and big. This one is tiny and the FC removes towards the top, so also useful in tiny flying wings. I created 2 versions, with and...
thingiverse
This was specifically designed to make it easy to mount the Matek F405 on the 36" Northern Pike ( https://www.thingiverse.com/thing:3040294 ), however it can be used on any aircraft that has room. The Matek easily slides into the mount from the...
thingiverse
Plate with clip for Matek f405 flight controller, nice tight fit, 4 holes 5mm diam. to fit shock absorbers. Need to remove memory card before sliding in flight controller. Designed in FreeCad 0.18, source file included, feel free to modify. ...
thingiverse
A mounting tray for the Matek F405 ***WMN*** flight controller. Has 3mm bolt holes (I used plastic nuts and bolts). I used a small double-sided 3M sticky pad to attach flight controller to tray. And I went as far as using thin double sided tape to...
thingiverse
AtomRC Swordfish Vista mount. Done with the left heel. ...Do not judge strictly.
thingiverse
Some of the parts I used in my AtomRC Dolphin build, as seen here https://youtu.be/_WoeBPlrSDc
thingiverse
AtomRC Dolphin esc plate. ...Print with no top layers or bottom layers to use your infill as ventilation
thingiverse
I have made smaller fins for the atomRC Swordfish. ...As a reference, I took the annotations from Andrew Newton's video https://youtu.be/DLr22CuZqJc
thingiverse
Replacement for the wooden base plate in the rear compartment of AtomRC Dolphin with two 30.5x30.5mm mounting places. I've printed using PETG. ...Fusion360 model included.
thingiverse
Aerodynamic and torque resistant motor mount for the Atomrc Dolphin. No support required. ...A regular motor mount plate and 4 M3x30 screws required
thingiverse
Rear landing skis made for the AtomRC KillerWhale. Tested in the snow and improved upon to this version. Reinforced to not snap in the cold. ... Please print at 100% size and with supports
thingiverse
Canopy for AtomRC Dolphin plane Designed in 2 parts top and bottom for supportless print I personally eSUN LW-PLA with 3% infill, 2 bottom layers Contains a hole for the DJI Vista antenna.
thingiverse
This is the AtomRC Dolphin vertical stabilizer For the Left stabilizer just mirror it in Cura. ... Designed for LW-PLA with infill 0% - total weight 9g PLA version will be around 20g+
thingiverse
Front Landing Ski for the AtomRC killer whale. Made after several versions the top is made to meet with a servo + horn. It is reinforced as to not break in the cold. ... Please print with supports PRINT AT 75% SIZE
thingiverse
Reference scans from AtomRC Dolphin. Note that the front canopy has been modified to maximise airflow through the front section of the aircraft. ... Produced by https://www.thingiverse.com/brogers123/designs using Einscan SE scanner by...
thingiverse
I got a AtomRC dolphin with a 1700kv ES2306 motor with a german 7042 prop. I put this values into ecalc and figured out, that on 4S the temperature of the ESC could rise to an unhealthy level. ...So I designed this air inlet for the ESC.
thingiverse
This is a "replacement" canopy for AtomRC Swordfish. This is just plain canopy with no mounts or something. It has enough clearance for 4s 21700. This model is not meant to be printed, rather, use it as a baseline for your own mods. Add your own...
grabcad
Mamba F405-mk2 Flight controller modeled in PTC Creo Parametric