audi r8 mini z 3d models
171849 3d models found related to audi r8 mini z.
thingiverse
This is an Audi R8 Spoiler. This is a close model to the wing that comes with the ASC/ white body kit. There is also the BBR HDF Spoiler from Bye Bye Racing. When scaling the (Wing), the length is 67mm. ...When scaling the (Supports), the height is...
prusaprinters
This is a replacement wing for the Kyosho Mini-Z Audi R8 body. It is shown on the 2015 year model, but it should work also on the 2010 year model (not sure about the 2016 model). </p><p>Styled after the wing on the 2010 model (not the same...
thingiverse
This is the Audi R8 Nose Mount for the metal piece. This metal part is on kenonhobby.com and the part#:BM001. When scaling this model, the length of the nose piece is 24mm and the spacers are 24.5mm. ...Sorry for the inconvenience.
thingiverse
Body mount for the Mini-Z body Audi R8 LMS. Has to be attached in connection with the spacers on the aluminum fornt body mount V2 from PN Racing. I'm using two of the 2.5mm spacer for the audi R8 LMS Body. ... Spacer Set ...
thingiverse
Spoiler for the Mini-Z body Audi R8 LMS. Has to be attached to the underside of the aluminum fornt body mount V2 from PN Racing. Grind down existing one if broken. ... Body mount clip for the Audi R8 LMS https://www.thingiverse.com/thing:5663374...
thingiverse
For mini z R8 LMS. ...The lowest quality body kyosho dumped out to the market.
thingiverse
Front clip for the Kyosho Mini-Z Audi R8 LMS MZN189. Print solid, with supports, and on its side for strength. This was made to print on a resin printer, so tolerance are tight. ... When printing on a FDM printer, you might be to file down or...
thingiverse
Front clip for the Kyosho Mini-Z Audi R8 Night Race MZN195. Print solid, with supports, and on its side for strength. This was made to print on a resin printer, so tolerance are tight. ... When printing on a FDM printer, you might be to file down...
thingiverse
This is a replacement front body mount for the Audi R8 LMS bodies for Kyosho Mini-Z RC models. You can print and use this replacement if your stock front body mount breaks and you cannot find an original replacement or don't want to wait for such to...
thingiverse
Kyosho's Audi R8 (MZN189) side clips. Same as stock, no mods made. These are NOT right/left specific. I print these on their side (as they would mount in the body) for strength, print solid, with supports. ...
thingiverse
Kyosho's Audi R8LMS (MZN195) always bugged me with the back end of the car being higher than the front and the side-to-side wobble when used with the MR03 chassis. Made some side body clips that lower the body 1.5mm, bringing the body level with the...
thingiverse
Rear wing for the Mini-Z Audi R8 LMS body of Kyosho. Could fit on other bodies as well. ... Parts holder and screw must be printed twice.
thingiverse
The Audi R8 LMS body is originally designed for 98mm AWD Mini-Z chassis such as MA-10 or MA-20 and is not intended for MR-02 or MR-03 RWD Mini-Z models, even though it will fit on them as well. When using the Audi R8 LMS body with a rear wheel drive...
thingiverse
This is an Audi R8 LMS Body Clip for the Pn Racing Adjustable Clip mount. I found that the carbon fiber one available from PN is skinny (1.94 mm) and doesnt fit well into the body, causing the front the shake. ...This one is slightly thicker to...
thingiverse
This is a work in progress project, a front body guard for the Audi R8 LMS body for Kyosho Mini-Z RC cars. You mount it on the chassis and it extends under the front of the Audi body to increase strength on impact when racing with the RC car. This is...
thingiverse
I made this body adaptor for https://www.thingiverse.com/thing:2039314 . ... Printed in in PLA with 0.2mm layer heigt and 100% infill
thingiverse
It is based on the Audi R8 body design from Michal Majer from Grabcad.https://grabcad.com/library/audi-r8-body-1 Thanks for your work! I have made some modifications and scaled it to fit to a MR03. i use the front adapter and the Rims(for offsets)...