autocad design template 3d models

But I would recommend using brim.All latest files can be found at Gitlab. BOM1x Adapter4x zip ties1x M4x20 bolt1x M4 nutSome rubber or electric tape to protect the rackAssemblySand, prime, paintInsert NutAttach adapter using M4 boltInsert zip...

 You could also do a three- or four-color print, of course—just make sure not to skip the “Contrast Test” section, below.This is designed so to be completed in two passes on a Prusa MINI (or in my case, one pass on each of two MINIs).  I...

Bases for Necron armies 17 different design! The Necrons are a mysterious xenos species of humanoid, robotic skeletal warriors that have lain dormant in their stasis-tombs for more than 60 million Terran years, though they have begun to awaken at...

If you scale the STL, the ballast will no longer fit as designed.  If you do not want to go through the trouble of the ballast, the model will still print perfectly, but will be better suited to play on dry ground.  I have printed with PLA,...

https://www.thingiverse.com/thing:1570168\r\n\r\nI wanted to upgrade my Tronxy P802MA to use the E3Dv6 hot end with a Bowden extruder without modifying my firmware, so I came up with an upgrade that only required purchasing an E3Dv6 clone.\r\n\r\nI...

This is the HULL for the 3d Printable Subnautica Cyclops I designed and built! The Sub is approximately 654mm in length. The whole vehicle has to be printed in separate parts which you will want to minimize support material used to reduce print time....

1:28 scale printed at 50%, finished model is 11" in length Donald Campbell's famous but ill-fated Bluebird K7, as it was configured at the time of his final 1967 attempt at the world water speed record at Coniston.I've yet to design the...

The BL Touch mounts are designed for extruder 1 and would need to be mirrored if used on extruder 2. You'll need left & right versions of the Mellow BMG Aero Wind (or a pair of Bondtech extruders). I used the 24v Volcano versions, with motors,...

If your primary goal was purely design-based you might simply import and play with this information using available graphical modeling softwares. If it had interactive component we would proceed with algorithms suited best for realising what we...

I designed the solution around mechanical parts I already had from a previous project. The exact parts I purchased come and go on Amazon, but similar parts seem to always be available. Here's what you will need: 1 @ 3D printed Perch Mount 1 @ 3D...

Welcome to Central Mexico!The Ancient Ruins Collection - Mesoamerica is a dedicated subcollection to the legacy of past civilizations in parts of what is present-day Mexico and Central America.This model was designed by Dany Sánchez.The Pyramid...

... than 4" from pivot to point and sheathed)</a>. Never be without a sharp pocket tool on a trip again.&nbsp;I love this tiny tool, I hope you find it useful, too!Designed in Solidworks for Makers.

Thingiverse/mikejeffs (https://www.thingiverse.com/mikejeffs/designs) Check out the videos on my youtube channel which include the engine in use and some simple build videos. YouTube Videos Full size and fully functional Short Shaft outboard motor...

I found several budget basketball hoops (affiliate links below) with 1.5” center poles and wanted to see if I could design an adapter with my limited 3d modeling skills. Finding the AquaStar dimensions on the vendor site and using Fusion 360 to...

I dissamble it to design a new one, reinforce it of course.This is from Leroy Merlin...

Note that for the 16T version, a bit of filing may be needed, since it was originally designed to use a couple of bearings instead of a real pulley. The 20T version is a remix of Elstak's version. For the hardware, I was able to use a lot of the...

The main files and documents can be found at: Thingiverse/mikejeffs (https://www.thingiverse.com/mikejeffs/designs) There is also an optional version with cooled top covers which can also be used with the steel leg. Thingiverse/mikejeffs...

The current design needs a razor knife to remove the supports, but they leave a clean surface which is essential as it's a mating surface. The base has a top mainly for when it's separated and if used to store parts or dice in. It's a tight fit,...

To this end, I've developed a cleat system.Required PartsThere are currently two different hanger designs on this repo, but both use the same cleat system.3D Printed Partsx2 Cleatsx2 Hangers (Either “Beefy” or “Skinny”)Mechanical PartsCommon Parts...

I tried in the design phase to make this enclosure as functional as possible, trying not to neglect a bit the aesthetic side that I don't mind looking after sincerely. The height from the slides to the lid (which I had to raise by 1cm by adapting...

Gingerly push the pen holder onto the heat sink – it's designed as a snug fit, so you may have to scrape it a bit to make it fit on just right. Hold it in place with the fan mounting spring clips. Mount the pen in place at the right height, send your...

Since I had my first 3D printer I wanted to do pieces for that but, alas, their design is very hard to print nicely (pins are too flimsy for a 0.4 nozzle, a 0.25 is too time-consuming). And, back then, I missed some pieces that didn't exist:...

&nbsp;The red areas designate the highest stress regions under this pull direction so if it fails due to overloading, it will likely fail at these points.The intent is to make this carabiner stronger than my previous ones, mainly due to it being...

I designed this for a .85" diameter broom stock. Let me know if you want another size added! The story continues... Lena was exhausted after a long day of cleaning the royal chambers and sweeping furiously throughout the palace. The monarch had...

Since no one offers a side charging handle for novak style sight cuts I designed a couple jigs that would allow you to file a piece of 1/2" or 3/4" round stock to fit the novak sight cuts to use as a side charging handle. Jigs 1, 2, and 3 are for...

I tried to design around it but there just isn't enough surface area down below to create large enough openings. I can run it at 60-70% and still get great prints and be much quieter than anything else I've tried The 5020 Axial fan will block the...

All part should be printed flat side down with no support needed.CaseRaft: noSupports: noLayer Height: 0.2mmInfill: 20 to 50% depending on your material strengthReelRaft: noSupports: noLayer Height: 0.15mmInfill: 100%References:Multipart Pinecil Case...

You get the picture).Change the PLA type to the one you are using for best results.Designed on Tinkercad. Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building...

The single glaring LED leaves a bit to desire, so I took this opportunity and designed this diffuser to even out the light and emphasis the text on the outer shell. However, before everything - !!!DISCLAIMER!!! By attempting to open up your 5X, you...

This is my portal gun design! I modeled the whole thing from scratch in fusion 360 and I'm really proud of the result. The models are each arranged in the orientation in which I printed them, so the printing should be fairly simple, I used...