avant devel drone 3d models
20734 3d models found related to avant devel drone.thingiverse
**********NOT TESTED********** Turtle fin for Avant Devel frame. ... Needs one cable tie to secure it on the top plate.
thingiverse
GoPro Session mount for Avant Devel (with axii u.fl mount). ... 01.09.18 Added 55° version
thingiverse
Little Axii mount for the Avant devel 5. Just push it over the rear standoffs. ...Print in TPU
thingiverse
This is a support for mounting a capacitor in Devel 5. ...With this piece the capacitor is firmly attached to the side of the standoff
thingiverse
soporte para la antena Lumenier AXII Stubby en el drone avant devel yo use ABS, 230º y cama a 95º con soportes solo para la zona baja.
thingiverse
Mount for Axii u.fl antenna for the Avant DEVEL 5 Hole distance = 24 mm (On one quad is the first prototype ) 11.11.17 Added new version with a small shark fin. ... 17.02.18 Added picture of Devel with shark fin.
prusaprinters
Mount for Axii u.fl antenna for the Avant DEVEL 5 Hole distance = 24 mm (On one quad is the first prototype ) 11.11.17 Added new version with a small shark fin. 17.02.18 Added picture of Devel with shark fin. Category: R/C Vehicles
thingiverse
Antena mount for Avant Devel5 drone. This piece allows you to have a really secure and resistant mount for your antena. I have made two versions: 1. Antena mount 2. Antena mount+capacitor mount Note: - If you print the normal version...
thingiverse
Foxeer Lollipop Antena mount for Avant Devel5 drone. This piece allows you to have a really secure and resistant mount for your antena. I have made two versions: 1. Antena mount 2. Antena mount+capacitor mount I have also added small gap below...
thingiverse
The mount is designed so that you can easily remove the gopro without having to undo any screws. Additionally the quad stays slim even when the gopro is removed because the mount is split into two parts and one of those can also be removed without...
prusaprinters
<p>Big shark fin with axii u.fl mount.</p> <p>One version with hole for two ws2812 LEDs.</p> <p>Needs to be printed in flexible filament.</p> Category: R/C Vehicles
thingiverse
Big shark fin with axii u.fl mount. One version with hole for two ws2812 LEDs. ... Needs to be printed in flexible filament.
thingiverse
Protection de barre avant de Drone Lethal SR-5
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=749887 Instructions Using the following options: textstring = AVANT wall = 1 basethickness_percent = 0.1 base_radius_add_percent = .1 RoundedBase = 0 shift_font_percent = 0.07 textheight = 10...
thingiverse
Wheels modeled for the 2014 Devel 16 prototype model. ...Meant to conform to hot wheels axle rods, if the wheel is scaled down that 2.2% the size of what it was.
cults3d
Car Devel Sixteen, a beautiful car in .stl and .obj format The images of the real car has made with a resolution of 0.2mm with a size X: 45mm Y:10mm Z:23mm with a speed 85mm/s at low resolution and lowest speed give better results.
sketchfab
today im happy to present you my 3D model of the devel sixteen prototype this model took 3 days of work it is by far my favourite car of all time and my first car to ever model hopefully i can make the trion nemesis next anyway i hope you enjoy it...
thingiverse
... @Bottom Non-Profit, you can customize the design to other avants. Commercial (Profit), please call the designer Visit our Drone Racing Team - https://www.fpvcrew.at or https://www.fb.com/fpvcrewstmk :) Designer: https://www.facebook.com/FPVLiNdi
thingiverse
I created this because I needed some place to mount an LED board on the back of my Avantquads Devel 4 frame
cgtrader
devel sixty 6x6 concept car The model was created in 3ds max 2014, vray 3.00 rendered. There are materials, render scene, different formats. different from the original model. there is no interior design. ...there is only exterior design.
thingiverse
LED & Cap holder for Avant Quad Xero Split 5 S Frame Combinated with https://www.thingiverse.com/thing:3470068 Material is TPU (Sainsmart)