axial scx10 chassis 3d models

This is an adapter to mount printed bumbers to Axial SCX10 cross member. This file contains two versions: Version 1: Adapter with post's Version 2: Adapter without posts, needs to be screwed on (single posts' are available at ebay, Amazon,...

I am making 8x8 RC with SCX10 axles so I needed two "pass-thru" axles. When using two same axle housing halves, you loose two pillars for mounting servo plate. I made a 4-link truss that integrates servo mounting pillars too. I recommend not to screw...

Body: 1x eBay Ram Clear Body SCX10 AX31132 Required Items: - x eBay M1.2x4mm Screw Optional: 1x Axial Racing Simple LED Controller w/LED lights (4 white and 2 red) 1x Axial Racing Universal 5 Bucket Light Bar Set More Photos Disclaimer: This section...

... To Secure The Tray In Place, We Recommend Using Longer 3x12mm (AXA436) Self-Tapping Screws That Will Provide A Rock-Solid Bond With The Chassis. ... Also Available: Relocation Mounts For Battery And RX For Enhanced Performance And Convenience.

This is my version of a durable lower control arm for the Axial SCX10. You just need 108mm M3 threaded rod and two of the original ball joints. Axial provided two different lengths of control arms. 114mm short wheel base (Dingo) and 121mm long...

... ... They are specifically designed to be mounted directly onto the Axial SCX10 frame rails, offering a flexible installation process that can be adapted by leaving them intact or trimming them at the notched section to achieve shorter overhangs.

Fits the side rails plastic part of the Axial SCX10-3 crawler. I decided that one of the domes has to be chopped off, which is not a big deal, as the sliders may still be fitted with the same screw from underneath into the ESC support. Dimensions...

This is a DIY rod end for Axial SCX10 or Capra I suggest printing them one at a time to avoid stringing and to minimize surface imperfection as much as possible because the fit is very tight. You may need a hammer to insert the ball into the rod but...

...... They are engineered for seamless integration onto the Axial SCX10 frame rails, offering the flexibility to adjust their length by either leaving them in their full form or carefully trimming them at the notched section to achieve shorter overhangs.

These are rock sliders that can be installed on the Axial SCX10 iii Basecamp.I printed these from Prusament PLA as a prototype and have yet to break them.  If they break, I plan to use some Prusament PC blend CF.You will need two M3x10 and two M3x6...

Servo saver 25t for mini servo of scx10.3.

** This is a snow plow designed specifically for the Axial SCX10.II (SCX10.2) Unimog UMG10. ** *** In theory, this should bolt directly onto any SCX10.II axle and frame, but you may need to add some shims or washers to secure the upper frame mount...

These are custom bumper brackets designed specifically for the Axial SCX10, created to accommodate a new body by extending both the front and rear sections. To optimize space, stabilizers were added to support the battery holder, which was relocated...

This is a skid remix created to fit an Axial SCX10 transmission onto the ECX G1 barrage. The transmission with motor was cheaper to purchase than the actual ECX upgrade G2 Motor Plate and 390 motor. I had to elevate the transmission slightly so it...

... them and it seams to work fine. You will need to get Axial Slipper pads AX31068, or you can print the one I included in PetG or TPU but I can't guarantee it will hold up long. ... This is a remix from https://www.thingiverse.com/thing:398515

rock slider remixed for scx10 ii build to share with everyone

Mounting plate for SCX10 transmission to mount 2 motor for more power at low speed

This is a closed narrow box for rc-receivers, to fit the right side-panel of the Axial SCX10-3 crawler. It provides 2 cable outlets (end and inner side). The goal was to replace the original and relatively huge Axial receiver box, so scale- builders...

I recognized that V1 only accommodated battery packs of the same size as mine, so this updated part places your SCX10's battery over the front axle and suits all chassis types. The first component fits above the bumper struts, while the second...

Below is the list of hardware required for this modification: - SCX10 II aluminum servo mount (you can find a good deal on Amazon); - M3 or M4 threaded rod (I opted for 4mm since I couldn't locate the 3mm option); - Rod ends (the included ones in...

just made this to fit the jci creep body for my scx10 ii thought I would share with the community

Here is a scale body for an Axial SCX10. Its an Oshkosh Hmett 4x4 body that requires supports depending on how it's printed. This isn't a straight print and place design yet, so you may have to mess with some parts to put them in place. Some parts...

These are bumper brackets for the Axial SCX10. Made these so that I could extend both the front and back to fit a new body. Also added stabilizers to use towards the battery holder as I had to move mine to the front. The battery holders will have to...

I've designed axial SCX10 2 Cherokee inner wheel wells to keep mud from entering the bodyshell. I created them using PLA, but a flexible material would be better, especially if you could switch materials and print the back support out of PLA or ABS...

People typically use axial 1.9 bead-lock wheels for off-road purposes.

... the outer holes on the stock shock hoops. This lift kit may fit other SCX10 models depending on shock position and geometry. Lift kit tabs are 4mm thick, identical in size to the stock spacer. ...To install, simply remove the stock spacer.

I design a scale, off road, front bumper for my Axial Scx 10 I. Happy with the result. Easy to print. ... Strong and durable even in PLA+.

SCX10 Front Mount Low CG Battery Tray. Strategically relocates battery weight directly over the front axles, dramatically improving vehicle balance. Engineered to handle oversized 5000mah batteries while minimizing zero binding...

I needed a bit more room underneath my SCX10 body. The stock side skirts were mounted too high and didn't seal the body well enough. So I came up with a design that adds three plates on each side, which now fit perfectly under the body. They provide...

Belt for servo and LC80 Kahr on the free man or scx 10 point two chassis