axial scx10 crawler 3d models
7738 3d models found related to axial scx10 crawler.thingiverse
TATRA 815 KAMAZ https://www.3drcbody.com for 22x22x22 table size. ... https://www.youtube.com/watch?v=TsANeUu8p74&t=5s&ab_channel=nzferby
thingiverse
These are bumper brackets for the Axial SCX10. Made these so that I could extend both the front and back to fit a new body. Also added stabilizers to use towards the battery holder as I had to move mine to the front. The battery holders will have to...
prusaprinters
These are bumper brackets for the Axial SCX10. Made these so that I could extend both the front and back to fit a new body. Also added stabilizers to use towards the battery holder as I had to move mine to the front. The battery holders will have to...
thingiverse
This is a simple sandtrack for your Scaler or Crawler. Lenght= 150mm width= 50mm Please hit "like" if you like it. Thanks Instructions Just print the part :-) Maybe you have to scale it x10.
thingiverse
Brought to you by http://RCNewz.com This is a scale winch designed to bolt right onto the front bumper of the Axial SCX10 II Jeep Cherokee RC rock crawler kit. ...It should fit nicely on many other trucks with a bit of drilling to the bumper of your...
thingiverse
Made this using axles and shocks left over from an upgrade to my Axial SCX10 2. The 8 suspension links and steering link are M4 threaded rod with Axial rod ends screwed on. The only thing I had to buy was an SCX10 gearbox, £9 from EBAY and £2 for...
cgtrader
This is a simple sandtrack for your Scaler or Crawler. Length= 150mm width= 50mm Please hit "like" if you like it. ... Thanks Stanley
thingiverse
Door handle for axial SCX10 Jeep Wrangler
cults3d
Axial SCX10 Trailer Hitch Bumper mount Scaler Crawler. Durch meine nun mehrjährige Erfahrung im 3D Druckbereich und etlichen versuchen mit verschiedenen Materialien von unterschiedlichen Herstellern, kann ich definitiv dieses Filament von...
pinshape
Axial SCX10 Trailer Hitch Bumper mount Scaler Crawler Durch meine nun mehrjährige Erfahrung im 3D Druckbereich und etlichen versuchen mit verschiedenen Materialien von unterschiedlichen Herstellern, kann ich definitiv dieses Filament von...
thingiverse
Version 2.0 RC Car Engine scale 1:10 Crawler Axial SCX10 now with cooling !!!! ...for 40mm & 30mm Fan
pinshape
Roof Rails for Crawler and Scaler. Durch meine nun mehrjährige Erfahrung im 3D Druckbereich und etlichen versuchen mit verschiedenen Materialien von unterschiedlichen Herstellern, kann ich definitiv dieses Filament von schmelz.bar empfehlen. ...
cults3d
Roof Rails for Crawler and Scaler. Durch meine nun mehrjährige Erfahrung im 3D Druckbereich und etlichen versuchen mit verschiedenen Materialien von unterschiedlichen Herstellern, kann ich definitiv dieses Filament von schmelz.bar empfehlen. Ich...
thingiverse
I just tweaked a few things for my project. The ESC tray was hitting the transmission cover. I used a 550 motor and the bigger motor was hitting the frame and battery tray. ...I also tweaked the bonnet to fit better, but I haven't tested fitment.
cults3d
Applicable to RC Crawler,such as D90,SCX10,Axial and etc. ... Weight:72g Size:6.5x8.5x5cm/2.56x3.34x1.96in lid is in two parts to reduce supports needed ,needs gluing
cults3d
RC Jack Stand for Cars, adjustable in height and width. Durch meine nun mehrjährige Erfahrung im 3D Druckbereich und etlichen versuchen mit verschiedenen Materialien von unterschiedlichen Herstellern, kann ich definitiv dieses Filament von...
pinshape
RC Jack Stand for Cars, adjustable in height and width. Durch meine nun mehrjährige Erfahrung im 3D Druckbereich und etlichen versuchen mit verschiedenen Materialien von unterschiedlichen Herstellern, kann ich definitiv dieses Filament von...
grabcad
https://www.amazon.com/gp/product/B07N1DYR42
thingiverse
For 3mm LED 4 screws 2mm
thingiverse
Made new taillightbuckets for my Axial SCX10 Rubicon crawler This thing was made with Tinkercad.
thingiverse
Fits the side rails plastic part of the Axial SCX10-3 crawler. I decided that one of the domes has to be chopped off, which is not a big deal, as the sliders may still be fitted with the same screw from underneath into the ESC support. Dimensions...
thingiverse
This is a 1/10 Scale RC car rifle rack I made for my Axial SCX10 Rock Crawler Kit. I plan to mount this on the back of the vehicle. The rifle rack fits weapons designed for 7 inch action figures which can be used in any dioramas too. It's about 3...
thingiverse
This is a closed narrow box for rc-receivers, to fit the right side-panel of the Axial SCX10-3 crawler. It provides 2 cable outlets (end and inner side). The goal was to replace the original and relatively huge Axial receiver box, so scale- builders...
thingiverse
If you have a Maverick Scout and like me you wanted to convert your Scout into an Axial SCX10 scale crawler - you're going to need one of these. The standard mid plate / chassis plate / motor mount / skid plate (whatever you wish to call it!) has the...
myminifactory
A replacement wishbone for an Axial SCX10 RC Crawler with lift kit. The lift meant the drivershafts were fouling the wishbone so I made new ones. ...They are slightly longer to adjust the axle for the lift also.
thingiverse
baca para crawler rc. ...especialmente para el axial scx10 2 k5 blazer pero se puede usar en el que quieras.
thingiverse
Muffler for the axial scx10-3 Jeep Gladiator. ... Designed to use the original screws.
cults3d
Cantilever system for use in crawlers such as Scx10. Adaptable to other car models. ...Needs bearings (8X4x3mm) and separators of 11mm.
thingiverse
Axial SCX10 Dingo parts radiator drivers floor center console Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2X Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 10 Post-Printing use double sided tape to affix to body