axial scx10 frame 3d models
109854 3d models found related to axial scx10 frame.thingiverse
ran my rock crawler into my kids trampoline and busted the front bumper. designed and printed a new one. hope this helps someone else. ...thanks.
thingiverse
These are designed for mounting on the Axial SCX10 frame rails, and can be adjusted by leaving them full lengths, or trimming them at the notched section for shorter overhangs. <i>Update 8/8/2018 XL and XXL Versions:</i> Per a user request I've...
cults3d
These are designed for mounting on the Axial SCX10 frame rails, and can be adjusted by leaving them full lengths, or trimming them at the notched section for shorter overhangs. Update 8/8/2018 XL and XXL Versions: Per a user request I've added 2...
thingiverse
Muffler for the axial scx10-3 Jeep Gladiator. ... Designed to use the original screws.
thingiverse
This is a bottom plate I created with a cradle for using the twospeed transmission from a Traxxas Summit in an Axial SCX10. This version is for using Axial OEM U-frame. Edit 16-07-08: Holes for links moved down 2mm to clear the frame. Cutout for the...
thingiverse
baca para crawler rc. ...especialmente para el axial scx10 2 k5 blazer pero se puede usar en el que quieras.
pinshape
SummaryThis is a bottom plate I created with a cradle for using the twospeed transmission from a Traxxas Summit in an Axial SCX10. This version is for using Axial OEM U-frame. ...The mount for the shiftingservo has to be cut out a little bit to fit the...
thingiverse
Simple exhaust print for axial scx10 (I). One screw (M3) mounts it to the stock frame brace bracket and you can use some zip ties to secure it more. ...Worked with my rc4wd bumper, not sure about the stock one though.
thingiverse
Axial SCX10 Dingo parts radiator drivers floor center console Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2X Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 10 Post-Printing use double sided tape to affix to body
thingiverse
... nach außen extrudiert damit man diese im nachhinein noch anmalen kann. Und den Verbinder hab ich auch noch neu gemacht Du brauchst: 1x Axial SCX10 III - Links 1x Axial SCX10 III - Rechts 2x Axial SCX10 III - Verbinder 2x drucken 8x M3 6mm Schrauben
thingiverse
I was playing around and decided to make a drift tire for my axial Scx10. The print time is about 6 1/2 hours on my Monoprice Select Mini V2. ...**note: These tires won't last forever you will eventually will have to reprint them.** Hope you enjoy.
thingiverse
### Axial SCX10 ii Light Bar As it says on the tin, a light bar for the scx10ii. Fits in the roof rack that comes with the Cherokee. I fastened it on by using 3mm nuts and bolts. ... I've included support for both 5mm and 3mm LED's, both take 11...
thingiverse
fits axial scx10 power wagon, possibly other models Instructions when you prepare the file, you will need to select "dont scale" if your software thinks that the thing can't fit. The rotation is off, and it will fit on a print bed at least 8 3/4...
thingiverse
Lift kit for all Axial SCX10 based RC trucks. Adds lift of 14, 20, and 26mm if the lower of the two upper mounts is used, the very top mount adds another 5mm. Pictures show mounting using 3mm hardware into the plastic (could use longer bolts + nut if...
cults3d
Cantilever system for use in crawlers such as Scx10. Adaptable to other car models. ...Needs bearings (8X4x3mm) and separators of 11mm.
thingiverse
A full Axial Deadbolt SCX10II Front Grill that includes a backplate that allows for the use of 5mm leds Print at 100% infill
thingiverse
I recently upgraded to a 5200kv brushless motor with 3s 5500 lipo and beat the snot out of my scx10. i broke the drivers side knuckle on the front axle. i've ordered aluminum replacements but couldn't wait to drive again so i designed and printed a...
thingiverse
Thickened up the sides a bit and made it so the box would slide between the frame rails. I used an existing hole in the frame and screw to secure it. Infill is up to you. Update: Went to fit my esc today and it was a bit tight. ...Added a second...
thingiverse
Clip is for blocking any cable inside the frame channel rear bumper for adding 4 lights with 8mm buckets front bumper is designed for fitting a winch and need 2 tubes 6mm and I used 8mm diameter tube for fitting the bumper on the chassis. grille...
cults3d
Clip is for blocking any cable inside the frame channel rear bumper for adding 4 lights with 8mm buckets front bumper is designed for fitting a winch and need 2 tubes 6mm and I used 8mm diameter tube for fitting the bumper on the chassis. grille is...
thingiverse
It is almost exactly the same as original part. ...Only for SCX10 (Scx10.1) axles. ... I made modified 4-link truss with servo mount too: https://www.thingiverse.com/thing:5898199
thingiverse
Front radiator for a rubicon body Axial SCX10 with support scaled Now is scaled!!
thingiverse
Axial SCX10 Front Steering Link Bar V2 - revised for a bit more clearance and front suspension travel.
grabcad
This part is meant to raise the bumper on the Axial SCX10 Honcho to fix clearance issues
thingiverse
this is a part for the Axial SCX10 to take the RX and the ESC on a plate
pinshape
SummaryThis is a bottom plate I created with a cradle for using the twospeed transmission from a Traxxas Summit in an Axial SCX10. This version is for using custom "flat" frame. ...The mount for the shiftingservo has to be cut out a little bit to fit...
thingiverse
This is a bottom plate I created with a cradle for using the twospeed transmission from a Traxxas Summit in an Axial SCX10. This version is for using custom "flat" frame. The mount for the shiftingservo has to be cut out a little bit to fit the cable...