b and d workmate 3d models
2315224 3d models found related to b and d workmate.thingiverse
Replacement B&D workmate handle. Uses then original roll pin to attach to workmate. ...Requires an m6 bolt to hold knob onto handle.
thingiverse
A tray to hold the bench dogs so they don't get lost or misplaced. ... Drill into the leg of the workmate and attach with three screws. ... There is a lip to easily line up the tray to the leg.
thingiverse
Had a missing footpad for my workmate Type 1 and made a simple design to replace a complex design. Replaced all 4 and printed in Black TPU.. ...Very nice snug fit, leg tube measures 20x30mm.
thingiverse
... :D Print Settings Printer: Monoprice Maker Select v2 Rafts: Yes Supports: No Resolution: 0.2mm Infill: 75% grid Notes: Didn't need to be 100% infill, with the 75% grid I could put all my weight on that corner of the table and the foot didn't mind.
cults3d
Took some measurements and roughed it up, printed off a lightweight prototype with minimal infill, and it worked! Printed it up four feet thicker with heavier infill and they work like a champ. Friends at work ask "couldn't you just have gone to the...
thingiverse
One of the best bits of kit I own is my trusty Black & Decker WorkMate. But I lost the plugin holder / clamps years ago. So this is a redesigned replacement for the missing clamps. ... The plug end is sized for 20mm (3/4inch) holes.
thingiverse
... on it. Print 2 of each plus a ¾" piece of plywood to fit the size you want. The front part has a square cutout, I used supports in there. If someone can reply with detailed photos of these supports, I'd love to update and correct my design!
thingiverse
... may not have a reason to display our logo. However, you may have a need for a nice looking "**d**". In fact, this versatile "**d**" model has been cleverly crafted to deliver elegant versions of "**b**", "**p**" and the oft-neglected letter "**q**".
thingiverse
très légère modification du fichier de base "Workmate spring by valknut": suppression de la languette qui empêchait la mise en place sur mon établi. Imprimé en PLA 0.2mm, 3 lignes de parois et remplissage 20% gyroide et supports Fonctionne a...
thingiverse
Replacement winding handle for black and decker workmate. I designed this in 2 parts in order to make the printing easier - it uses the original pins to connect it to the winding bar When assembling, the parts need to be firmly pushed the last...
3docean
This file contains a workmate made in Cinema 4d. ... Filetypes included: .c4d .3ds .obj .stl .fbx .dxf
prusaprinters
Large lower foot and smaller triangular foot for Black and Decker Workmate WM5XX. These fit well and have been on mine for some time now. I printed these in Rigid Ink TPU with the speed slowed to about 20mm/sec. I still get a bit of stringing on the...
thingiverse
Replacements for the cranks and "swivel blocks" on the Black and Decker Workmate Portable Project Centers. Instructions I initially modeled both the crank and block in Sketchup. However, I wanted a simple OpenScad project, so I re-did the crank in...
thingiverse
... of http://www.thingiverse.com/thing:146333 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=146333 Instructions Using the following options: size = 30 right_initial = B your_font = write/knewave.dxf left_initial = D
thingiverse
......http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: message = D.B!!! ...hole_radius = 3 font_size = 12 stick_thickness = 3 font_thickness = 6 stick_width = 7 flat_bottom = 1 Font = write/Letters.dxf
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=146304 Instructions Using the following options: left_initial = D heart_size = 30 right_initial = B your_font = write/Letters.dxf
thingiverse
The fit is nice and snug and since the printing leaves ridges along the Z-axis, the friction is large between both the workmate and clamp (which is also ribbed). I did not simply duplicate the original but instead improved the design. Mine has a...
thingiverse
This is a replacement for the smaller rubber feet that the Workmate WM225 WM425 / WM400 series rests on when it's extension legs are not folded down - Black and Decker part number 242394-00. This is not an exact replacement due to my limited Sketchup...
thingiverse
Thanks for sharing the model of the worktop block! ...The one I printed was just a bit too fat around the keyhole fit, so I made it a bit thinner with Tinkercad and printed it with PETG.
thingiverse
Fills the gaps between the flying frame and the roto clamp in d&b y and v series
cults3d
... Design is based on common center body, A, B and C variants vary in their wings and tail flaps and the number of Stealth pods for short-range missiles. The D variant features major modifications for VTOL capabilities and large-caliber forward gun.
thingiverse
This is a 50mm blower fan shroud and mount for the 3-wheeled D-Bot/B-Bot Titan extruder back plate (http://www.thingiverse.com/thing:1833172) Looks a bit like a lobster claw to me. I haven't printed it yet, but I plan to try it out this weekend. It's...
thingiverse
I made new worktops for an old workmate and made the drawings in case you want to build of the workmate as platform for something else or use as a fixture. I used 18mm ply rather than MDF. You can CNC them but no 3D print unless you have very...
thingiverse
Replacement handles for the Black and decker workmate adjustable work surface bench. One knob option has snaps the other is intended to be used with a nut and bolt. ... Attaches to drive shaft with a set pin.
thingiverse
Lost some of these on my workmate over the years so modeled one up and printed. ... Works well.
thingiverse
... for strength along the spindle. You will need an M5 roll pin for the crank and a penny washer and m6 bolt for the handle. ...It will fire straight into that 'cosmetic' thread and lock up when it reaches the washer leaving the handle to turn freely.
thingiverse
I downloaded a customized nut and edited it in Tinkercad. Works great. ...Print Settings Rafts: Doesn't Matter Supports: ...
thingiverse
this is a washer/track slider for a older bench top workmate product. ... It allows the benchmate to tilt at an angle and is held in by a 1/4 wing bolt.