b and z motors 3d models

(most notably the single Z axis motor upgrade designed by RRacer, i have also modified that design and that can be found on my uploads page). I recommend 5 perimiters with at least 30% infil to keep it fairly sturdy. I have printed mine at 0.2mm...

This is a model of 3 hypersonic rocket cases for Estes B and C engines. The engines should slide into the cases perfectly. If not, make corrections in an editor. Glue the cones to the top to cap it. ... THESE ROCKETS ARE NOT RECOVERABLE.

This is my synchro of the Z axis. ... It is not the best design, but it works. uses standard pulleys 20 teeths and 1020 mm belt. ... It uses two ball bearings 8/16/5 mm material is PETG, but PLA will be fine too.

oldham Z coupler for RepRap with downside z motors and anti woobling

Z couplings for Piper 3d printers and other 3d printers. 3 sizes for M8 thread, 5/16, and 3/8th. Fusion files are included. ... https://piper3dprinters.com

Created this mount for model rockets that use B and C motors and tube type RT-60. This mount can be stackable, which will allow for aligned rocket ignitions. Mounts will release themselves after motor releases parachute release charge and will tumble...

Created this mount for model rockets that use B and C motors and tube type RT-60. This mount can be stackable, which will allow for aligned rocket ignitions. Mounts will release themselves after motor releases parachute release charge and will tumble...

Customized version of https://www.thingiverse.com/thing:248635 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=248635

Replacement of mounts of stepper motors for the Z axis.

A simple piece to replace the three original parts that hold the Z-axis motors and both rods. Sometimes the rod was vibrating, creating vibrations while making noise, this part solves this problem and ensures a stable hold of the axes and the...

Zaribo Z motor mounts for top of the frame. ...Mirror along X axis for the left one.

I found that i needed a little extra extension from the frame to accommodate my dual Z motor at the same time as a PSU shroud with front loading AC supply. ... https://www.thingiverse.com/thing:3639621

I'm using GT2 pulleys on new Z motors (had to swap original ones for the ones with dual shaft) bottom shaft, GT2 idler on the printed part and 2GT-852 closed belt motors are driven each with it's own driver linked to same step/dir pins and this belt...

Movement indicator of the Z axis motors, also useful for checking any misalignments (which on my printer happens practically at every print)For a better result I suggest to print it in two colors. ...For example if you use repetier server use these...

Z stop extension that goes on the x axis, I made it to be used with the BLV Ender 3 Mod and Ender 3 Z-Axis Damper Mount by AndiArbeit90 which can be found in the remix source files.

Motors and Automation

ES51 Motors and Chassis

OMRON Z-15GM-B

540 and 550 motor models to help with design work.

Faulhaber motors

... is of 5kgf-cm operates on 2A. ...In ordered to be used it also needs a coupler. The high rpm motor is of 200 rpm. The servo motor is of 1kgf-cm but gives very good feedback. The motors can be controlled with help of arduino and L298 motor driver

This is a classic D.B.Z. ...character "the werewolf".

Electrical microswitch Микропереключатель Z-15GW2-B 220VМикропереключатель с лапкой 15А 250VAC

Improved mount for the Z axis motors on my CTC I3 printer.

A small upgrade for the Prusa i3 R2 by Nicola P. ...They are a simple reinforcement for the NEMA Z motors supports. ...Between the motor and the reinforcement I put a cork sheet.

just my remix of the tarantula brackets from Elzariant ,without botoms.I use 2 step motors for dual z .

http://www.thingiverse.com/apps/customizer/run?thing_id=56209 Instructions Using the following options: overlap_factor = 19 polygon_edge_thickness = 2 knot_width_top = 50 P_A_T_T_E_R_N = 0 radius = 19 pattern_yes_or_no = 1 tie_thickness = 1.8...

http://www.thingiverse.com/apps/customizer/run?thing_id=56209 Instructions Using the following options: knot_width = 33 tie_height = 450 sides = 7 radius = 19 B_O_D_Y = 0 polygon_edge_thickness = 2 overlap_factor = 19 tie_width = 95 knot_thickness =...

I designed this one to place the motor a little lower in the frame and to keep all amount of extra printing inside the bed movement area as little as possible, and seeing as how I like everything lined up perfect I added the alignment bumps. No...

Our in-house team of 3d artists handle all further remodelling, materials conversions and other adaptations to deliver best possible visual and technical quality of all the additional file formats and renderers we offer. Files units are centimeters...