backup camera mount 3d models

Rendering of a Jeep backup camera mount using spare tire as the mount location. ...

Lexus GX470 Backup Camera MountThis model is a simple 3D printable mount for attaching an aftermarket backup camera to the OEM mounting location on a GX 470 SUV. The mount was designed for use with this "NATIKA Backup Camera IP69K" however it may...

This is a backup camera mount for an NC Miata with the Advanced Keyless Entry (AKE) package. It a derivative design originally posted by "kiddingme". It is designed around the Nakita backup camera and moment buttons available on Amazon. It...

The mount for my generic chinese backup camera rusted away. I made a new one. ... Guaranteed to fit as long as you happen to have the same camera.

The mount for my generic chinese backup camera rusted away. I made a new one. Guaranteed to fit as long as you happen to have the same camera. ...

You'll need: - (1) license plate-mounted backup camera, like this one: https://amzn.to/2RIzj3C - (2) Sheet metal screw, American #10 size, flanged hex head, at least 5/8" long - (4) M3 socket-head or button-head cap screw, 10 mm length - (4) M3...

Human error led to a broken third brake light, prompting me to install a backup camera on the fly. ...I quickly switched out the faulty component with a shiny new one, using square nuts for added stability and 3mm by 16mm bolts for precision.

I enhanced this by adding a hole in the center to accommodate a small backup camera, which has a slimmer rim around its edge to match the latches on the device. Improved version: http://www.thingiverse.com/thing:767820 Instructions...

This is a remix from License Plate Camera Mount by MongooseNX with just a few modifications to fit my camera from Niloghap Universal on Amazon. Link for camera. ... ...

This mirror installation is intended to assist with parking and does not provide a good angle (camera is mounted too low) for full time use while driving. This mount is designed to be used with two brass heat set inserts and four M3 screws. ... The...

... I put double sided alien tape a well as two car clips to attach it (had to drill two small holes for the car clips). I hot glued the camera from the back to seal it in and left the front just pressed against the opening with no extra protection.

Backup camera mount for Honda Element

... 99mm and removed obstructive tabs, increased height for smooth camera nut rotation. Tinkerverse remix: https://www.tinkercad.com/things/h3eG5m1y3jM-jeep-backup-camera-mount Make your own adjustments by ungrouping and fine-tuning to fit your needs.

This thing is a backup camera mount that relocates your aftermarket backup camera to a hitch mounted bike rack to enable a clear view behind it. This is designed to fit a Kuat rack but may also work with others. First, when you install your...

Needed a Mount for My Backup Camera After Taking Off My Chevy Silverado 2500's Tailgate and Adding a Utility Cap. Used ABS Material to Make It. I Chose These Printer Settings to Get It Done Right. ... Printer: Powerspec Rafts: Doesn't Matter Supports:...

Made for my 2007 Toyota FJ Cruiser, I purchased a brand new radio featuring an LCD screen and discovered it came equipped with backup camera capability thanks to the provided camera. However, I was unaware of where exactly to position it until I...

Since I preferred positioning the camera directly in the center of my RV, I designed and 3D printed a custom mounting plate that replaces the original aluminum bracket. The new plate is then attached to the vehicle using strong Gorilla Mounting Tape,...

Fort transit reverse camera mount on roof

Fort transit reverse camera mount on roof

I needed a more sturdy dash mount solution for my backup camera that I use on my camper. The screw holes in the sunglasses tray on the ram seemed like the perfect place for it and this is what I came up with. It fits my leekooluu (off brand...

Since I wanted to have the camera in the middle of the back end of my RV, I created a mounting plate that replaces the aluminum bracket and gets mounted to the vehicle using "Gorilla" mounting tape. ...I used PETG since this is for outdoor use. Parts...

Camera Mount for Jeep JK, Mounts onto spare tire lug nuts that came with the Smittybilt spare tire carrier. ... The following camera was used: https://www.amazon.com/dp/B071R3HJ6Q?ref=ppx_pop_mob_ap_share

I made a mount that looked like it belonged on the car more. Printed in ASAused 6 walls to hopefully make it water proof. Also available on Onshape to be modified "Ioniq 5 Auto Vox Rear Cam Mount”V2 - now has angled base to match spoiler better and...

This was designed an tested on a 2008 S2000 CR.This fits the RAYOO L002 "2-in-1 Universal Rear View Camera"

Dodge Ram1500 Backup Camera MountYear: 2015 Dodge Ram1500 (May fit other model years)Adapted to utilize existing holes for dash board coin area.Compatible for Type-S after market rear camera LCD, utilizing Bluetooth license plate camera.Additional...

This is a mount I assisted with the design of for our backup camera. ...It fits the camera from the set available here: https://www.amazon.com/gp/product/B06XKPQ6YZ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 It was mounted using M6 nuts and bolts...

Hi All, This is an adapter that lets you attach a NATIKA WD-011 camera available on Amazon to the factory backup camera location on a Gen2 Toyota Tacoma 2005-2015. I have a 2008 model that didn't come with the factory backup camera, so I got a Pop &...

I admired Kuruma1's innovative hitch camera mount, but I realized that printing it with my current setup would be a significant challenge. Therefore, I decided to create my own version, tailored to work seamlessly within the constraints of my...

Holds the BC40 on a good angle using the stock spare tire on the back. ... Attach to the spare tire with large zip ties. When the camera is not working, go the back and clean the mud off the lens. ...:)

Remixed from https://www.thingiverse.com/mr_mjd to fit on my 1996 Mazda Miata Fastback, but I'm pretty sure it can fit many other vehicles with the US Plate layout.