ball and socket mount 3d models

This file describes a parametric ball and socket mount that could be used to position a small, lightweight object at a specific angle (e.g. a touch-on LED closet light that is aimed at an object of interest). The socket has screw holes for attaching...

So I created this ball-and-socket mount. It's got adjustable screw holes, but I'm just using sticky-tack for mine. Please see the customizer for the various ways the design can be adjusted. Print Settings Rafts: No ...

... of the parts up or down to suit your printer calibration. Can be printed without support but I suggest a high infill to increase strength in the fingers and waist of the ball. ...You can attach through the centre hole or either of the corner holes.

TX02 ball and socket joint mount. Allows the camera angle to be quickly adjusted as well as allowing good cooling. ...

Ball socket joint to allow GoPro freedom of movement while stands on any magnetic surface mainly but you can really use any other sort of stand. ...as long as is GoPro.

Customized version of http://www.thingiverse.com/thing:1085548 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1085548 Instructions Using the following options:...

Customized version of http://www.thingiverse.com/thing:1085548 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1085548 Instructions Using the following options:...

SummaryCustomized version of http://www.thingiverse.com/thing:1085548 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1085548InstructionsUsing the following options: ballSize = 15 flangeDiameter = 40 flangeThickness =...

This is the merge of G-Clamp and Socket and Ball Mount Simply because the G-Clamp does not have any kind of mount This probably can be used to hold phones/tablets/cameras that require adjustments of the angle.

A 2040 extrusion Mount for this ball and socket design. Using it to run wire for 12v LED tape on an AM8, passing the wire through the center of the ball/socket joints. ... Still a work in progress, the code is incredibly messy right now

... ...Allows you to attach the camera to a ball and socket chain for better positioning. An M3x25 screw and nut connect the camera to the mount to replace the original Logitech stand. ...(The screw only needs to be > 16.5mm, 25mm is not necessary.)

Okay, in the 3rd revision, I increased the gap between the ball and socket to 1.5, which allowed the ball to go in without breaking the socket. But you will need to place some sticky back foam (I used weather stripping) in the bottom of the socket to...

Allows you to attach the camera to a ball and socket chain for better positioning. An M3x25 screw and nut connect the camera to the mount to replace the original Logitech stand. ...(The screw only needs to be &gt; 16.5mm, 25mm is not necessary.)</p>...

i made a few different versions of a ball an socket mount for a wifi camera i have that i use with my printers an its been pretty handy so far. hope its helpful to someone else. ...if it doesnt fit ur camera let me know an i'll try to make one that...

Customized version of http://www.thingiverse.com/thing:1085548 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1085548 Instructions Using the following options:...

Customized version of http://www.thingiverse.com/thing:1085548 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1085548 Instructions Using the following options:...

Customized version of https://www.thingiverse.com/thing:1085548 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1085548

Took the 20x20 piece of the bottom for putting it into smaller things

Customized version of http://www.thingiverse.com/thing:1085548 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1085548 Instructions Using the following options:...

A ball-and-socket wall mount for a camera. It's Customizable! Adjust it to fit your specific needs! I used it along with http://www.thingiverse.com/thing:120272 to hold my PS Eye cameras in a VR setup. Then I changed them out for Oculus Rift...

The original ball and socket mounts would hit either the left Z axis motor, my extruder, or the right door of my lack enclosure (depending on how I was trying to install it). ...I just made the arm a bit longer so it fits my setup.

Camera mount plate with ball and socket flexible arm. Link as many as you want together to create a flexible arm. ... This is a 1" ball that is compatible with RAM style mounts.

Please note that, once the wire is glued to the socket part with the lever in place, it is impossible to pull the ball out of the socket without destruction, even when the lock is fully disengaged. Printing ---------- I successfully printed it...

Prints separately and then snaps together. ... I used mounting tape to stick it to the wall and attach the sensor to it.

Customized version of https://www.thingiverse.com/thing:1085548 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1085548

Customized version of http://www.thingiverse.com/thing:1085548 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1085548 Instructions Using the following options:...

Customized version of https://www.thingiverse.com/thing:1085548 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1085548

Customized version of https://www.thingiverse.com/thing:1085548 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1085548

Customized version of https://www.thingiverse.com/thing:1085548 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1085548

Customized version of http://www.thingiverse.com/thing:1085548 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1085548 Instructions Using the following options:...