ball head mount 3d models
492637 3d models found related to ball head mount.thingiverse
Simple ball head mount. I used these to mount fish-eye camera to walls. I use 3M 200MP double-sided tape to attach faceplate to camera's back. ...
thingiverse
The ball head mount I used was this one: https://www.amazon.com/gp/product/B01CQAQOSI/ You'll need the a screw to attach the ball head mount to the bracket. You could also use it without the ball head mount. ... It was made to be used with this: ...
prusaprinters
I created this bracket to hold my Logitech Brio webcam on a ball mount, but it could be used for any webcam that supports the standard tripod mounting bolts. The ball head mount I used was this one: https://www.amazon.com/gp/product/B01CQAQOSI/...
thingiverse
Convert a Velbon DF-10ML Tripod to use a ball head. ... Threaded Inserts used (from McMaster-Carr): 1/4"-20 Thread × 1/2" qty.2 6-32 Thread × 1/4" qty.6 1/4" To 1/4" or 1/4" to 3/8" Camera Screws from Ebay.
prusaprinters
I use these to mount indoor fish-eye IP cameras to walls and ceiling. ...Use transparent sticky pads to attach it to camera housing if it's lightweight, or drill holes and use screws.</p>
thingiverse
Thin but workung ball head wall Mount for teufel CS 25 FCR Speaker. ... As long teh angle isn´t too much, speakter woun´t fall out :) (used for my surround speakers)
thingiverse
The ball head of the mount is a standard steel 20mm ball bearing. You can find them everywhere pretty cheaply e.g. on aliexpress: https://www.aliexpress.com/item/32923245920.html Do not use stainless steel balls, they are not ferromagnetic enough to...
thingiverse
This is ball head raspberry pi camera mount to 2020 frame. Camera module is cheap knock off from aliexpress - you may want to design your own part for original camera. ...Module stays rather loose, but you can use double sided tape to fix it.
prusaprinters
This is a swivel head mount for the Philips Hue Motion Sensor. The ball head of the mount is a standard steel 20mm ball bearing. You can find them everywhere pretty cheaply e.g. on aliexpress: https://www.aliexpress.com/item/32923245920.html Do not...
thingiverse
... for a 7.1 Atmos rear high speaker System and designed a mount which is moveable on top of my closets. ...Because this cheap Cambridge ones are common speaker systems hopefully someone can use it as well ;-) Even fits tight on ball head without screw.
thingiverse
Remixed the vent mount to include a 17mm ball head. May fit other Audi models. ...Enjoy.
thingiverse
I put it above my working space with an enlarger stand and a massive ball head with 2" x 1.6" quick release plate. The weight of the phone occasionally causes a unscrewing and the video pin on the plate doesn’t work with the ring light. So, I...
thingiverse
Wrench for the Elgato mount ball head that comes with the Key Light and a bunch of other Elgato lighting hardware. ... Had such a hard time tightening and loosing the little knob that comes with the ball head so this just fits over the knob and adds a...
thingiverse
... instead? This should work with a 15mm ball, but you could probably modify and mix it to work in other scenarios, too, for example, just screwing a camera to it with a standard ¼" bolt. I have yet to test it, but will update when I do. ...
prusaprinters
so I figured, why not connect THAT to the camera arm, instead? This should work with a 15mm ball, but you could probably modify and mix it to work in other scenarios, too, for example, just screwing a camera to it with a standard ¼" bolt. I have yet...
thingiverse
The "AdapterArm_Bowl" as well as the wall mount uses a small "ridge" which fits into the golf balls holes - so in certain angles, the assembly holds even tighter. For printability I separated the bowl and the arm. If you don't need the "ridge", you...
thingiverse
In this case I'm using a Joby Ball-Head X The mount has a counter-bored hole to fit a single 1/4-20 screw you will need to attach the camera or ball-head. ... Update: v2 now has a support rib under the bracket for less sag with heavy cameras, and...
thingiverse
Hey there, here is a wall mounted flexible camera arm with a ball head and a standard camera mount. You will need a few M5 / 40 Hex bolts with wingnuts and big washers and two short M3 Bolts for the Ball Head. The arms are angled in 15 degree...
thingiverse
Mount (adapter) for 3D Printed Tripod Ball Head V2 ( https://www.thingiverse.com/thing:3483656 ) for tripod from ring lamp AL-18 https://youtube.com/shorts/Tkp_UG_cEXM?feature=share The quick mount plate and mechanism which you see in video are here:...
cults3d
Mount (adapter) for 3D Printed Tripod Ball Head V2 ( https://www.thingiverse.com/thing:3483656 ) for tripod from ring lamp AL-18 https://youtube.com/shorts/Tkp_UG_cEXM?feature=share The quick mount plate and mechanism which you see in video are here:...
thingiverse
I am trying to create a ball head mount for a camera. The ball will be a 'hardwood doll head' I picked up at Micheals (42mm or 1 5/8"). This first run has at least one flaw: I didn't build anything into the base to attach it to the tripod because...
prusaprinters
The ball head was originaly made as base for hand vise (therefore M6 adn M8 threads). ...It can be also used as photographic ball head with 1/4" and 3/8" thread.
thingiverse
The ball head was originaly made as base for hand vise (therefore M6 adn M8 threads). ...It can be also used as photographic ball head with 1/4" and 3/8" thread.
thingiverse
This is the 4mm ball-head that goes along with the socket connector uploaded here: http://www.thingiverse.com/thing:52172 Instructions You can sink the ball-head in any object so that it fits within the object. ...Then the socket will fit flush to the...
grabcad
Ball head mount for Dacia ventilation grill.Fits on smartphone mounts or navigation systems etc.Easy to hook on and remove.
thingiverse
This is a simple ball head joint with roughly 15° of freedom all around. You can glue or screw it to the parts... Has a snug fit but you can adjust tolerances by in- or decreasing the size of one part. Corser layerheights generate more...
thingiverse
Simple designed head for a Golf Ball Retriever to catch a ball and get them of the water. The Golfball simply stuck in the hole so you can lift them up. ...Just put the head on a teleskopic bar.