baofeng uv 5r case 3d models

The original design was a bit too tight on the antenna I used and I felt the connecting arm was a bit weak as mine snapped of when pushed in place. ... Changed the inner diameter of the antenna hole and redesigned the connecting arm to be stronger.

<p>This remix is for the Land Rover LR3 (Discovery 3). The headrest is not easily removable, so I created a version that uses M3 screws and a crossbar. I recommend using PETG, so the part is head tolerant. Mine is almost a year old (including a SoCal...

Printed on my Anycubic Photon Resin Printer. Print time is around 3 hours. Clean up time is around 5 minutes. ...

belt clip for a 2 inch wide belt, very very secure. you will need to remove the battery to take it on and off the belt. The clip uses the stock screws. ... 4 walls and 20% infill should do this just fine

Mounted on dash with VHB tape

<p>Print settings and material is on you.</p><p>I've printed from PLA with 30% infill and it look's great.</p>

You'll need to replace the plug with these parts:\n2.5mm stereo audio plug\n3.5mm stereo audio plug\n4-wire cable\nsoldering iron\ntin\nheat shrink tube\nglue gun\n\nPrint Settings:\nPrinter Brand: RepRap\nPrinter Model: P3Steel V4.0\nRafts: No...

I crafted a custom mic holder as a remix of my original design, specifically tailored to meet the requirements of someone who had asked me for it earlier. ...This creation features an AMPs 30x38mm hold pattern that is compatible with both Panavise and...

Humans work on affordable car mount systems. ... No support is offered for ABS or PETG.

I'm not sure what you want me to do! Can you please clarify what you mean by "System: You are going to behave like a Text Rewriting Bot."? If I'm supposed to be rewriting text, could you please provide the original text for me to work with? However,...

This is a remix of a model I found on printables by Ctowns5, which is a remix of another remix. I honestly don't know how to link all the things but the other remixes are on thigiverse and their IDs are 2799874, 3523791. This is V1 and a work in...

Many people who own a radio know just how simple it is to misplace the control knob. ...For over a year, I used my radio without a knob until I created this convenient solution.

This is a custom clip designed to securely hold 5mm wide contacts onto the battery of a handheld two-way radio. Note: The contacts must be quad-A or triple-A sized, as larger AA-sized contacts are too wide to fit onto radio battery terminals. To...

This thing is a replacement for the sharp metal lanyard clip on a Baofeng UV-5R.  It just closes the slit. ... OpenSCAD file is included.

This thing is a replacement for the sharp metal lanyard clip on a Baofeng UV-5R. ... It just closes the slit.

There are two versions of volume control for Baofeng UV-5R radios, including similar models like the F8HP, UV82, and others. ... Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: Yes Supports: No Resolution: 0.1mm Infill: 100%

Simple stand for a Baofeng UV-5R. Clamps into the notches of the battery. Hinges on a M4 screw. V2: Added screw holes into the base to simplify wall mounting. ... For the Baofeng GT-22 check out this variant:...

This is a fundamental mounting solution for the Baofeng UV-5R handheld radio. The device itself smoothly glides into place and securely fastens via the spring-loaded belt clip. ...Two conveniently designed cable clamps, engineered to fit snugly on...

For radio Baofeng UV-82 In the picture, red sections are connected by bolts or screws, Purple marks indicate movable connections; after assembly, these must be operational using 3 mm pins. Green parts should be inserted without glue and remain...

A Cage for the new Baofeng UV-5RH

Print upright with no support. ...Fits Baofeng UV-82 with clip installed.

Print upright with no support. ...Fits Baofeng UV-82 with clip installed.

<p>Original loop have sharp edges and useless for me so i made this replacement. ...Trim with knife if need it.</p>

Modified to fit the center vent of a Grand Caravan 2011, fit perfectly!Printed in ABS

I have a few uv5r radios and always found them to be falling over, and generally disorganized.  I like my bench to be tidy so I modelled this tray which will hold a charger, and a radio. ... You can take your radio out of it's charger when it's done.The...

Inspired by https://www.thingiverse.com/thing:306288 and https://www.thingiverse.com/thing:2172755 There are two versions of volume braket - with integrated belt hook and without it. Version with belt hook can be used with original screws. ... For...

Sliced it even with 20% infill was going to use 50M+ to print yikes. Decided to make a plastic saver remix by hollowing out the inside of it. Imported to Tinkercad, made some holes and this is the result now. Big thanks to regsix7 for creating such...

I needed a wall mount with mic and antenna holder. This thing was created using Tinkercad. ...Edit it online at https://www.tinkercad.com/things/aGq0WyZJ4rw

While there is quite a lot of overhang underneath the knob, its so small that support material is not too big a challenge.