barb fitting 3d models

A 1/2-inch stainless steel barb connection for attaching a 10mm hose, available in either 304 or 316 grade stainless steel, suitable for use with both water and steam.

9.6mm Barb Fitting

Through-hole barb fitting 3mm with nut

NXP mpxh Map series barb fitting

Print settings: For the barb fitting I printed standing up with the thread side up Used supports for touching the build plate only printed at 0.2 resolution with 45% infill 3 walls For printing the nut I increased the size of the part to 102%...

A Luer-to-barbed connector designed specifically for use with 1/8-inch inner diameter tubing, aimed at females.

1/2 inch BSP thread barb fitting to fit 12 mm diameter pipe

This is a 0.2 inch ID five-way barb fitting engineered specifically to match up with a one-quarter inch six-millimeter inner diameter hose.

A G1/4"-threaded barb fitting is available for PC water cooling systems, compatible with 1/2" inner diameter tubing. ...Ideal for designing personalized PC builds and modifications; based on actual product specifications.

This design contains: - the barb fitting (rounded or with a hexagonal face) - a nut to screw on from the outside - rings to be used as seals - a wrench for the hexagonal fittings I created this design to get rid of waste water from my countertop...

Here is the rewritten text: This is a compact 0.2-inch ID, three-port Barb connector designed to fit almost all 1/4-inch (6 millimeter) inside diameter hoses.

1/2" Barb with bottle cap to catch spent primers

A compact 0.2-inch four-arm barbed connector designed specifically for attaching 1/4-inch or 6-millimeter tubing.

strait, thread in fitting, 1/8 bsp

Barb fitting for a TotalPond 140 GPH Fountain Pump model # 52217 The barb fits 3/8" ID hose The lower portion fit's into the 13mm hole on the fountain pump. ... Printed standing straight up, I used supports around the bit of overhang around the base of...

A custom-made hose barb fitting is used in my car for the turbo boost controller. The threads are 1/8" NPT, and the hose barb accommodates approximately 5/16" rubber vacuum hoses, with compatibility for 1/4" hoses as well. ...I printed the fitting at .1...

Barb Fitting G1/4" a 3/8" for Custom Watercooling The design was made in Fusion 360. I used PLA + and then gave it a layer of UHU Expanded Polystyrene to prevent any leakage in the piece. ... HOSE USED: - Diameter: 3/8 "(9.5mm); - Thickness (wall):...

In order to mitigate this issue, I took the precaution of supporting the air hose, thus preventing any pressure from being applied to the fitting when it was in a softened state. After utilizing the fitting for three consecutive days, I am pleased to...

... it into the compressor. The compressor gets warm and softened the PLA print. I had to support the air hose so it did not put a force on this fitting when it was warm, used it for 3 days in a row so far no leaks. ... use at your own risk :-)

I created my own airpump adapter for my laser cutter since the original one didn't come with the required fittings. To get it fast, I designed and printed this in PLA plastic and wrapped some teflon thread tape around it before screwing it into the...

Remix to fit a 4mm hose on the barb side.

This is a fitting for a water pump requiring 1/2 FNPT to 1/2 ID tubing barb. ...Modified for 3d printing no supports.

Kitbashed ¼ NTP male to male ½ hose barb.

Print it barb side up.The barb is 13 mm at the narrowest and 15.6 mm at the thickest, works perfectly for ½" PVC tubing, though getting it off can be tough. 

I created two types of adapters: one has a single barb and the other has three. Each one comes in both solid and hollow versions. The solid version might be useful if you need to drill a single hole through it, going all the way through. Most of...

It is designed to allow for easy drainage, since the existing parts I found available didn't allow for good drainage due to surface tension around the inlet.You might need to play around a bit with the tolerances, the easiest thing to do is to just...

... connection that can withstand pressure variations. Barb fittings come in different designs, each suited for specific applications and hose materials. ...The versatility of these couplings makes them a popular choice across various industries.

The pumps are common but I could not find a tapered barbed fitting anywhere for it. It works surprisingly well when printed in the right orientation. The threaded fitting would not fit quite right for some reason, so it is an m12 fitting scaled by...

Here is the air assist: https://www.thingiverse.com/thing:2421971 So, I wanted something I could glue into the hole for the hose that had a barbed fitting, so I designed my own. It is design so that NO supports are needed at all. Even the ring...

Customized version of https://www.thingiverse.com/thing:2858709Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2858709