barb insertion tool 3d models

A clamp and barb insertion tool for quick and hassle-free shortening of Shimano brake hoses. Keeps the hose in place and makes it easy to insert the tiny barb into the end of the cut hose. Probably works with any other hydraulic disc brake with ~5 mm...

I made this to have some better control over the insertion of 3mm threaded inserts instead of using a soldering iron. I have a 40mmx3mm screw through it with a nut inset to hold it in place. The two other nuts have loctite applied and tighted...

Wire Loom Insertion Tool 穿线器 直径分别有8,10,15mm

This is one of the tools we use at MakerBot to insert the PCB standoffs.

This tool allows DIMM modules to be lifted from a tray and inserted into the slots. without any skin contact and provide a larder surface area. ... this tool is for DIMMs without heat sinks.

@@ 這是個失敗的作品 This is a failed work 個人參考用..... ... Personal reference 使用方法請參閱 https://electropicks.com/products/wire-loom-insertion-tool http://www.moko999.com/

Pen tube insertion tool. Keeps fingers out of the glue. ... Perhaps a little longer than I needed (didn't have a dimensioned prototype to copy).

This is a handle that can be used in conjunction with Phoenix Contact's Insertion/Extraction tool PN 1658794 (VS-IET-DSUB-SIGNAL-STD). That tool is for installing and removing D-Sub contacts from HEAVYCON modular inserts. The model will need to...

A quick tool I made to insert a spring and gasket into a sink. I struggled for 5 minutes trying to put the spring and gasket into place and finally gave up and printed this tool. I don't really expect anyone to download this, probably better to...

... pushing LEGO pins into places. This is very easy print, very tolerant to layer thickness, the only thing is your printer shall be halfway properly calibrated in the XY dimensions, so that the pin has the right amount of friction in the tool hole.

Pen tube insertion tool. Keeps fingers out of the glue. ...Perhaps a little longer than I needed (didn't have a dimensioned prototype to copy). Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Yes Supports: Yes Resolution: 200 Infill: ...

make to open the extruder pusher in order to insert easily filement

I got fed up with bending drawing pins and hurting my thumb pushing them in when I was putting up the Christmas decorations so came up with this little tool; put a little Blu-Tack or sticky modelling clay to hold the pin in place and then grip the...

Simple tool for pressing Safety Eyes in place when making stuffed animals. Attach the tube-part in the handle with a drop of superglue or something similar. Prints without support or anything like that. ...It has a small notch under the front edge...

I whipped up this "thingy" the help insert the PCV valve and allow you to get enough leverage the easily push it into the valve cover without breaking the new valve.I i rounded the top to make it easier on your hand and the inside is stepped to fit...

I whipped up this "thingy" the help insert the PCV valve and allow you to get enough leverage the easily push it into the valve cover without breaking the new valve.I i rounded the top to make it easier on your hand and the inside is stepped to fit...

This tool makes it easy to apply an even amount of force across the whole chip without digging a hole in your thumbs or hands, using either the top curved surface against the heel of your palm or the two thumb depressions on either side. ...

This tool works great at inserting 608 bearings into fidget spinners. Does not press on the inner race, only on the outer bearing race. ... ENJOY!!!!!

Then with the conical hollowed-out end of the tool pointing inward, you feel for the tube and catch it in the slot on the side of the tool. You can then rotate the tool and push it gently down on the end of the receiver to push the receiver and dome...

This is a tool I made based on the idea I saw at http://weldingweb.com/showthread.php?168191-Internal-o-ring-inserter-tool My '71 John Deere 4320 tractor has some hydraulic dowel pins (JD part R41511) that (during a clutch replacement) require a new...

In the photo on the top is a $20 spoke nipple insertion tool, (I'm not affiliated with BHS but am a very happy customer) it's a really nice piece of steel with a taper on the pointy end that creates a friction fit when inserted in the top of a spoke...

In the photo on the top is a [$20 spoke nipple insertion tool](http://www.bikehubstore.com/product-p/mulfing.htm), _(I'm not affiliated with BHS but am a very happy customer)_ it's a really nice piece of steel with a taper on the pointy end that...

This handy little device helps insert the Vex metal axles into tight gears or assemblies without putting a hole in your palm.

Also in this item, I'm making an item similar to the arnnworx tool : http://www.arnnworx.com/catalog/index.php?main_page=product_info&cPath=71&products_id=327&zenid=64f4c3b8b371ceb4d4caa71ec03e0d2a The arnnworx tool includes three screws that you...

Sample cap insertion tool. ...Ion chromatography

A simple tool to align and insert the nock in the arrow shaft. ...So far the tool was only tested with Easton nocks but should work for most.I recommend printing it with 100% infill

Here's a model I made of a Daniels MFG. ...M81969/17-07 insertion tool. Modeling this tool was kinda pointless but it may be useful if you're creating assembly instructions. ... Daniels MFG P/N - DAK55-4B Military P/N - M81969/17-07

http://www.thingiverse.com/apps/customizer/run?thing_id=678211 Instructions Using the following options: textsize = 16 direction = up fontname = Dancing Script baseheight = 1 RoundBase = 1 base_radius_add = 3 textstring = Barb text_excenter_factor =...

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: font_size = 10 stick_thickness = 3 font_thickness = 5 Font = write/orbitron.dxf message = Barb stick_width = 8 hole_radius = 3 flat_bottom = 2

http://www.thingiverse.com/apps/customizer/run?thing_id=45424 Instructions Using the following options: build_plate_selector = 0 tagH = 20 indent = 2 radius = 10 line2 = GRUDZIEN line1 = BARB Font = write/orbitron.dxf edge = 4 build_plate_manual_y =...